D-Link DWS-3160-24TC - Page 833

DWS-3160 Series Gigabit Ethernet Unified Switch CLI Reference Guide
829
type - Specifies what action should be taken if a packet matches the rule's criteria. The
possible values are Permit or Deny.
deny - Specifies that the action that will take place, if a packet matches the rule's criteria, is
deny.
permit - Specifies that the action, that will take place, if a packet matches the rule's criteria,
is permit.
match_every - Specifies to match every packet. Valid values are true or false.
true - Specifies that every packet is considered to match the selected ACL Rule.
false - Specifies that it is not mandatory for every packet to match the selected ACL Rule.
srcip - Specifies the source IP address of the IP ACL rule.
<ipaddr> - Enter the source IP address, of the IP ACL rule, here.
srcmask - Specifies the source netmask of the IP ACL rule.
<netmask> - Enter the source netmask, of the IP ACL rule, here.
dstip - Specifies the destination IP address of the IP ACL rule.
<ipaddr> - Enter the destination IP address, of the IP ACL rule, here.
dstmask - Specifies the source netmask of the IP ACL rule.
<netmask> - Enter the destination netmask, of the IP ACL rule, here.
src_layer4_port - Specifies the source Layer 4 port match condition for the IP ACL rule.
domain - Specifies that the source Layer 4 port match condition will use to port number of
the service called Domain.
echo - Specifies that the source Layer 4 port match condition will use to port number of the
service called Echo.
ftp - Specifies that the source Layer 4 port match condition will use to port number of the
service called FTP.
ftpdata - Specifies that the source Layer 4 port match condition will use to port number of
the service called FTP Data.
http - Specifies that the source Layer 4 port match condition will use to port number of the
service called HTTP.
smtp - Specifies that the source Layer 4 port match condition will use to port number of the
service called SMTP.
snmp - Specifies that the source Layer 4 port match condition will use to port number of
the service called SNMP.
telnet - Specifies that the source Layer 4 port match condition will use to port number of
the service called TELNET.
tftp - Specifies that the source Layer 4 port match condition will use to port number of the
service called TFTP.
other - Specifies to use a custom port number that the source Layer 4 port match condition
will use.
<int 0-65535> - Enter the custom source Layer 4 port number used here. This value
must be between 0 and 65535.
dst_layer4_port - Specifies the destination Layer 4 port match condition for the IP ACL rule.
domain - Specifies that the destination Layer 4 port match condition will use to port
number of the service called Domain.
echo - Specifies that the destination Layer 4 port match condition will use to port number
of the service called Echo.
ftp - Specifies that the destination Layer 4 port match condition will use to port number of
the service called FTP.
ftpdata - Specifies that the destination Layer 4 port match condition will use to port number
of the service called FTP Data.
http - Specifies that the destination Layer 4 port match condition will use to port number of
the service called HTTP.
smtp - Specifies that the destination Layer 4 port match condition will use to port number
of the service called SMTP.
snmp - Specifies that the destination Layer 4 port match condition will use to port number
of the service called SNMP.
telnet - Specifies that the destination Layer 4 port match condition will use to port number
of the service called TELNET.
tftp - Specifies that the destination Layer 4 port match condition will use to port number of
the service called TFTP.
other - Specifies to use a custom port number that the destination Layer 4 port match