DADISICK GFL-F Series - User Manual

User manual for GFL-F series
laser ranging sensors
！
Warn
● The light source of this product uses visible semiconductor lasers. It is prohibited
to directly or indirectly reect the laser beam from the reecting object into the eye.
If the laser beam enters the eyes, it may pose a risk of blindness.
● This product does not have an explosion-proof structure. Prohibit use in
ammable, explosive gas or explosive liquid environments.
● Do not disassemble or modify this product as it is not designed to automatically
turn o laser emission when the body is opened. If the client disassembles or modies
this product without authorization, it may cause personal inju, re, or electric shock
hazards.
● The use of controls, adjustments, or operational procedures beyond those
specied here may result in hazardous radiation leaks.
！
Reminded
● It is ve dangerous to wire, connect/disconnect inteaces when the power is
turned on. Please make sure to turn o the power before operation.
● Installation in the following locations may cause malfunctions:
1. A place covered with dust or steam;
2. Places where corrosive gases can be generated;
3. A place that will directly receive splashed water or oil;
4. Places subjected to severe vibration or impact.
● This product is not suitable for outdoor use.
● Do not use this sensor in an unstable state sholy after the power is turned on
(approximately 15 minutes of warm-up time)
● If it is necessa to use a switching power regulator, please ground the grounding
terminal. Do not connect to high-voltage cables or power lines. Operation failure will
lead to induction or damage faults, as each product has dierences, so there may be
slight dierences in the detection characteristics of the workpiece.
● Do not use this product in water.
● Please do not disassemble, repair, or modify this product without authorization, as
it may cause electric shock, re, or inju to the human body.
● Wipe o dust on the transmitting or receiving components to maintain proper
detection. Avoid direct impact of external objects on this product.
● Operate within the rated range.
！
This product cannot be used as a safety device to protect the human body.
Dimensions
Wiring method
Technical Parameters
NPN+Analog+RS485
PNP+Analog+RS485
+ V
Brown
Pink
External
Input
Black
Control
Output
External
Input
Blue
0 V
+
-
12V-24V DC
±10%
The main circuit
AGND
White
Yellow
Gray
Analog
Output
Shield
Analog Ground
AGND
Analog
Input
Device
RS485(A+)
RS485(B-)
The main circuit
AGND
+ V
Brown
Pink
Black
Control
Output
Blue
0 V
External
Input
Gray
Analog
Output
Shield
Analog Ground
AGND
White
Yellow
RS485(A+)
RS485(B-)
Analog
Input
Device
External
Input
12V-24V DC
±10%
+
-
load
load
★: Indicates the measurement distance. In harsh environments, such as when the sunlight is too strong, the ambient
temperature uctuates too much, and the reective suace is dark, the measurement results will have larger errors. In
this case, the use of a target reective plate will be better.
Resolution
Measurement error
Laser type
Voltage
Current consumption
1mm
+(2mm+d*1/10,000)★
Red semiconductor laser Class II laser 655+10nm<1mW
12V-24VDC+10% pulsation P-P10%
≤50mA @24V
NPN or PNP open drain output
Open drain collector transistor output
Maximum current:50mA
Applied voltage: less than 30V DC
Residual voltage: less than 1.5V
Leakage current: less than 0.1mA
Control output
Output action
Sho circuit protection
Analog voltage output
Analog current output
Reaction time
External input
Protective structure
Operating temperature
Storage temperature
Working humidity
Use ambient illumination
Use elevation
Cable
Material
Quality
Normally open/normally closed can be switched
Automatic recove type
Output range: 0-5V (alarm: 5.2V) Output impedance: 100Ω
Output range: 4-20mA (alarm: 0mA) Output impedance: 300Ω max
50-200ms
NPN contactless input
IP67
-10C~+45℃ (be careful not to condense or freeze)
-20℃~+60℃
35%~85%RH
Incandescent lamp: light receiving suace illumination below 3000lux
Below 2000m
With 8-core composite cable 2m
Aluminum pas
About 150g
Item
Model
NPN+analog+485
PNP+analog+485
Measure distance
GFL-F100NM-485
GFL-F100PM-485
GFL-F200NM-485
GFL-F200PM-485
0.1-1m 0.1-2m
GFL-F500NM-485
GFL-F500PM-485
0.1-5m
Item
Model
NPN+analog+485
PNP+analog+485
Measure distance
GFL-FM10NM-485
GFL-FM10PM-485
GFL-FM20NM-485
GFL-FM20PM-485
0.1-10m 0.1-20m
GFL-FM50NM-485
GFL-FM50PM-485
0.1-50m
Display and Buttons
Threshold setting
Output indicator light
The current value
Learning key
+/options
-/options
Set up

DADISICK GFL-F Series Specifications