DAELIM S3 User Manual

M6×1.0
M6×1.0
M6×1.0
M10×1.25
M6×1.0
M10×1.0
M12×1.25
M6×1.0
M6×1.0
M6×1.0
M16 1.0
M8×1.25
M6×1.0
M6×1.0
M5
M30×1.5
M7×1.0
M12×1.25
M28
M12 1.25
M8×1.25
M8×1.25
M8×1.25
M8×1.25
M6×1.0
Engine oil applied
1.0 ~ 1.2
1.0 ~ 1.2
1.0 ~ 1.2
3.5 ~ 4.5
1.0 ~ 1.2
1.5 ~ 1.7
1.6 ~ 2.0
0.8 ~ 1.2
1.0 ~ 1.4
0.35 ~ 0.5
6.0 ~ 6.7
3.0 ~ 3.4
1.0 ~ 1.2
1.0 ~ 1.2
0.35 ~ 0.5
1.0 ~ 1.2
1.0 ~ 1.4
5.0 ~ 6.0
5.0 ~ 6.0
5.0 ~ 6.0
3.0 ~ 4.0
3.0 ~ 4.0
1.6 ~ 2.0
1.6 ~ 2.0
1.0 ~ 1.4
CYLINDER HEAD COVER BOLT
CAP HOLER BOLT
CAM CHAIN GUIDE BOLT
CYLINDER HEAD SOCKET
CYLINDER BOLT
SPARK PLUG
ENGINE TEMPERATURE SENSOR
TENSIONER PIVOT BOLT
TENSIONER LIFT BOLT
TENSIONER LIFT SCREW
ACG FLYWHEEL NUT
STARTER CLUTCH OUTER SOCKET
OIL PUMPASSBOLT
OIL SEPERATOR
ACG STATOR COMP SCREW
TAPPET ADJUST HOLE CAP
WATER PUMP IMPELLER
DRIVE FACE NUT
DRIVE PLATE NUT
CLUTCH OUTER NUT
MISSION COVER BOLT
MISSION CASE BOLT
MISSION COVER BOLT
MISSION COVER CHECK BOLT
STARTER MOTOR BOLT
※Torque values listed above ate for specific tightening points. Torque values for other items are listed in the following tables.
4㎜BOLT, NUT 4㎜SCREW
5㎜BOLT, NUT 5㎜SCREW
6㎜BOLT, NUT 6㎜SCREW
8㎜BOLT, NUT 6㎜FLANGE BOLT,NUT
10㎜BOLT, NUT 8㎜FLANGE BOLT,NUT
12㎜BOLT, NUT 10㎜FLANGE BOLT,NUT
※SH(Small Head) : presents 6mm bolt of 8mm flange head
0.15 ~ 0.4
0.45 ~ 0.6
0.8 ~ 1.2
1.8 ~ 2.5
3.0 ~ 4.0
5.0 ~ 6.0
0.15 ~ 0.3
0.35 ~ 0.5
0.7 ~ 1.1
1.0 ~ 1.4
2.4 ~ 3.0
3.5 ~ 4.5
(SH Flange bolt included)
(SH TYPE included)
SERVICE INFORMATION

DAELIM S3 Specifications

General

Fuel System	Carburetor
Transmission	5-speed
Front Suspension	Telescopic Fork
Front Brake	Disc
Rear Brake	Drum
Seat Height	780 mm
Engine	4-stroke
Engine Type	4-stroke
Rear Suspension	Dual shock
Fuel Tank Capacity	12.5 L