To Next PageTo Next PageHow to fix Daikin FTXM50M ON/OFF TIMER if it does not operate according to the settings?
If your Daikin Air Conditioner's ON/OFF TIMER isn't working right, check if the ON/OFF TIMER and the WEEKLY TIMER are set to the same time.
Why is the cooling/heating effect poor in my Daikin FTXM50M Air Conditioner?
If your Daikin Air Conditioner isn't cooling or heating well, consider these possible causes: * Check if the air filters are clean. * Make sure nothing is blocking the air inlet or outlet of the indoor and outdoor units. * Ensure the temperature setting is appropriate. * Verify that the windows and doors are closed. * Confirm that the airflow rate and direction are set correctly.
What to do if my Daikin Air Conditioner operation stopped suddenly and the OPERATION lamp flashes?
If your Daikin Air Conditioner operation stopped suddenly and the OPERATION lamp is flashing, take these steps: * Ensure the air filters are clean and clean them if necessary. * Check for any obstructions blocking the air inlet or outlet of the indoor and outdoor units. * Turn the breaker off, remove any obstacles, and then turn it back on. Try operating the air conditioner with the remote controller again. If the lamp continues to flash, contact the service shop where you purchased the air conditioner.
What to do if Daikin FTXM50M operation stopped suddenly and the OPERATION lamp is on?
If your Daikin Air Conditioner suddenly stops and the OPERATION lamp is on, it might be due to a large voltage fluctuation. The air conditioner will automatically resume operation in about 3 minutes for system protection.
Why Daikin Air Conditioner does not operate (OPERATION lamp is off)?
If your Daikin Air Conditioner does not operate and the OPERATION lamp is off, check the following: * Ensure that a breaker hasn’t turned off or a fuse hasn’t blown. * Confirm that there isn’t a power failure. * Verify that batteries are correctly installed in the remote controller. * Make sure the timer setting is correct.
Why hot air does not flow out soon after the start of HEAT operation in Daikin FTXM50M Air Conditioner?
If hot air doesn't flow out soon after starting HEAT operation on your Daikin Air Conditioner, it's likely because the unit is warming up. Allow 1 to 4 minutes for the system to reach a certain temperature before it starts discharging air.
Why Daikin FTXM50M remote controller does not work properly?
If your Daikin Air Conditioner remote controller isn't working, the batteries might be weak. Replace all batteries with new AAA.LR03 (alkaline) batteries.
Why does mist come out of the indoor unit of my Daikin FTXM50M Air Conditioner?
If you notice mist coming out of the indoor unit of your Daikin Air Conditioner, it could be due to the air in the room being cooled into mist by the cold airflow during COOL operation or cooled by the heat exchanger and becoming mist during defrost operation.
What to do if an abnormal functioning happens during operation of Daikin FTXM50M?
If your Daikin Air Conditioner is functioning abnormally during operation, try turning the breaker off, then turning it back on. Afterward, try operating the air conditioner using the remote controller.
Why does the outdoor fan rotate while the Daikin FTXM50M Air Conditioner is not in operation?
The outdoor fan of your Daikin Air Conditioner may continue rotating for another 60 seconds for system protection or when the outdoor temperature is very high.
General| Brand | Daikin |
|---|---|
| Model | FTXM50M |
| Category | Air Conditioner |
| Language | English |
Essential safety warnings and precautions for operation, installation, and maintenance.
Guidelines for proper installation site selection and electrical work safety.
Instructions for installing batteries and mounting the remote controller holder.
Explains comfort airflow and intelligent eye sensor functions for enhanced comfort.
Addresses common non-trouble occurrences like sounds and airflow stopping.
Guides on diagnosing and resolving issues like no operation, poor cooling, or abnormal functioning.
Explains how to use the remote controller to display error codes for fault diagnosis.
