Why does my Daikin Heat Pump emit an odor?
If your Daikin Heat Pump emits an odor, it's likely due to room smells and cigarette odors that have accumulated inside the indoor unit. To resolve this, the inside of the indoor unit must be cleaned.
General| Model | RZQSG100L8Y1B |
|---|---|
| Category | Air Conditioner |
| Type | Split System |
| Cooling Capacity | 9.5 kW |
| Heating Capacity | 10.8 kW |
| COP | 3.61 |
| Outdoor Unit Noise Level | 52 dB(A) |
| Cooling Capacity (BTU/h) | 32400 BTU/h |
| Power Supply | 220-240V, 50Hz |
| Refrigerant | R-410A |
| Operating Temperature (Cooling) | -10°C to 46°C |
Details the version history of the service manual, including release dates and changes.
Provides essential safety warnings and precautions for handling the equipment and performing repairs.
Specific safety guidelines and warnings relevant to personnel performing repair work.
Important safety instructions and warnings for the end-users of the equipment.
Explains the meaning of various icons used throughout the manual for clarity.
Introduction to the service manual and its scope for the RZQG-L & RZQSG-L series.
Identifies available indoor and outdoor unit models and their combinations.
Provides visual representations of different outdoor unit models.
Defines the limits for cooling and heating operation based on temperature.
Details on wired remote controllers, including applicable models and functions.
Explains the buttons and display elements of the wired remote controller.
Configuration procedure for using two remote controllers with one indoor unit.
How to set group numbers for centralized control systems.
Information on wireless remote controllers, including applicable models and functions.
Procedure for setting wireless remote controllers as MAIN or SUB.
Accessing and using the service mode for maintenance.
Specific service mode functions for the BRC1D528 controller.
Specific service mode functions for the BRC1E52/53 controller.
Explains the role of key components and thermistors in the system.
Visual logic diagrams for cooling, dry, and heating operations.
In-depth explanation of various operational functions.
Details on indoor unit specific functions like thermostat and fan speed.
Details on outdoor unit specific functions like abnormal stops and restart.
Conditions and reasons for abnormal unit shutdown.
Procedure for unit restart after a stop.
System protection against low pressure conditions.
System protection against high pressure conditions.
Procedure and conditions for defrost operation.
Modes and procedures for emergency operation.
Steps and precautions for performing initial system tests.
Essential checks before conducting test operations.
Verifying remote controller settings before operation.
Detailed procedure for executing the test run.
Important safety and operational notes for test runs.
Initial troubleshooting for installation-related failures.
Configuring system parameters using the remote controller.
Specific field setting procedures for wired controllers.
Step-by-step guide for setting mode on BRC1D528.
Step-by-step guide for setting mode on BRC1E52.
Table of configurable settings for remote controllers.
Procedure for setting wireless remote controllers.
Details on indoor unit settings and their corresponding codes.
Summary of field settings applicable to outdoor units.
How to configure settings for quieter operation.
Function to limit power consumption based on demand signals.
Configuration for low humidity environments to improve capacity.
Configuring settings directly via the outdoor unit PCB.
Identification of physical controls on the outdoor unit PCB.
Procedures for making settings using BS buttons.
Detailed steps for configuring settings in Mode 2.
Procedures for routine maintenance checks.
Diagnosing issues based on observed symptoms.
Troubleshooting steps when the equipment fails to start.
Diagnosing issues when only the fan runs.
Troubleshooting intermittent operation.
Diagnosing problems with unit restart.
Troubleshooting lack of cooling.
Troubleshooting lack of heating.
Troubleshooting white mist discharge.
Troubleshooting noise and vibration issues.
Troubleshooting the "88" display error on the remote controller.
Using LED indicators for troubleshooting.
Diagnosing issues using indoor unit LEDs.
Diagnosing issues using outdoor unit PCB LEDs.
Using the remote controller for troubleshooting.
Steps for performing self-diagnosis.
Comprehensive list of error codes and their explanations.
Troubleshooting indoor unit PCB failures.
Troubleshooting drain water level errors.
Troubleshooting indoor fan motor issues.
Troubleshooting errors related to capacity setting.
Diagnosing transmission errors between PCBs.
Troubleshooting thermistor related errors.
Troubleshooting humidity sensor system errors.
Troubleshooting motion and floor sensors.
Troubleshooting outdoor unit PCB failures.
Troubleshooting high pressure switch related issues.
Troubleshooting pressure sensor actuation.
Troubleshooting compressor motor lock.
Troubleshooting outdoor fan motor issues.
Troubleshooting electronic expansion valve errors.
Control based on discharge pipe temperature.
Troubleshooting high pressure switch system.
Troubleshooting low pressure switch system.
General troubleshooting for thermistor system errors.
Troubleshooting errors related to the outdoor unit PCB.
Troubleshooting overcurrent detection.
Troubleshooting stall prevention.
Diagnosing transmission issues between control and inverter PCBs.
Troubleshooting power supply imbalances.
Troubleshooting errors in capacity setting.
Alert for refrigerant shortage.
Error code for refrigerant shortage.
Troubleshooting power supply voltage issues.
Diagnosing multiple potential issues between units.
Troubleshooting transmission errors between remote and indoor units.
Troubleshooting transmission errors between main and sub remote controllers.
Troubleshooting errors related to field setting switches.
Diagnosing address duplication in centralized controllers.
Troubleshooting transmission errors between centralized and indoor units.
Visual representations of system piping.
Specific piping diagram for the RZQG-L9V1 model.
Visual representations of system wiring.
Wiring diagram for the outdoor unit.
Technical data on R-410A refrigerant properties.
Procedure for safely removing the switchbox.
To Next Page
