Audio data (linear setting with subsonic filter)
Maximum output power per channel (THD + N < 0.5%, all channels
driven)
10D: CF = 6 dB @ 4/8 ohms 4 x 700 /350 W
10D: CF = 12 dB @ 4/8 ohms 4 x 700 /350 W
10D: Maximum output voltage 82 V
30D: CF = 6 dB @ 4/8 ohms 4 x 1000/800 W
30D: CF = 12 dB @ 4/8 ohms 4 x 1600/800 W
30D: Maximum output voltage 117 V
Frequency response (—1 dB) 35 Hz – 25 kHz
THD+N (20 Hz – 20 kHz, 200 W @ 4 ohms) < 0.5%
S/N ratio (unweighted, RMS)
Analog input (10D/30D) > 101/104 dBr
Digital input (10D/30D) > 103/106 dBr
Damping factor (20 Hz – 200 Hz into 4 ohms) > 80
Crosstalk (20 Hz – 20 kHz) > —45 dBr
Gain (Linear mode @ 0 dB) 31 dB
Protection circuits
Output current protection
45 A
Overvoltage protection Up to 400 V AC
Self-resetting overtemperature protection
Output DC offset protection
Output HF Voltage Limiter
Output pop-noise suppression
Power supply
Universal range switched mode power supply with active power
factor correction (PFC)
Mains connector powerCON
Rated mains voltage 100 to 240 V, 50 – 60 Hz
Mains fuse internal
Power consumption (typical values)
Standby
9 W
Idle 48 W
Max. power consumption (short term RMS)
10D: 1.3 kW
30D: 2.2 kW
Automatic Standby -tbc-
Audio input connectors
Analog INPUT (A1 - A4) 3-pin Phoenix Euroblock male
also used as link output wired in parallel
Pin assignment GND, neg., pos.
Input impedance 38 kOhms, electronically balanced
Common mode rejection (CMRR @ 100 Hz/10 kHz) > 60/50 dB
Maximum input level (balanced/unbalanced) +23/29 dBu
+27 dBu @ 0 dBFS
Digital INPUT (D1/2, D3/4) 3-pin Phoenix Euroblock male, AES3
Pin assignment 1 = GND, 2 = AES Signal, 3 = AES Signal
Input impedance 110 ohms, transformer balanced
Sampling rate 48/96 kHz
Synchronization Word-Sync: PLL-locked to source (slave mode)
Digital LINK (D1/2, D3/4) 3-pin Phoenix Euroblock male
electronically balanced
analog signal buffering (refresh), power fail relay (Bypass)
Output connectors
SPEAKER OUTPUTS A/B/C/D
2 x 4-pin Phoenix Euroblock female
Network connectors
CAN
2 x RJ 45 parallel
ETHERNET 2 x RJ 45
Dual Ethernet port with built-in 2-port Ethernet switch
10/100 Mbit
GPIOs/FAULT contact
GND (
) / GPIOs 1 – 5 1 x 6-pin Phoenix Euroblock male
Opto-coupled (galvanic isolation)
DC voltage 24 V DC (±25% / 18 V DC – 30 V DC)
Maximum current draw 1 A
Source resistance 5.4 kΩ
Diode forward bias 1.2 V
FAULT contact 1 x 3-pin Phoenix Euroblock male
Controls
POWER
Mains power switch (rear panel)
RESET Reset button (rear panel, recessed)
Indicators
POWER
Power indicator (green)
Data Data stream indicator (yellow)
Mute A/B/C/D Channel mute indicator (red)
Channel/Device error indication
ISP A/B/C/D Input Signal Present indicator (green)
GR A/B/C/D Gain Reduction indicator (yellow)
OVL/Error A/B/C/D Overload/Error indicator (red)
4. Technical specifications
d&b 10D/30D Manual 1.10 en 9
To Next Page
Loading...
