Danfoss VLT AutomationDrive FC 302 - 6 Options and Accessories Overview; Fieldbus Devices

6 Options and Accessories Overview
6.1 Fieldbus Devices
This section describes the eldbus devices that are
available with the VLT
®
AutomationDrive FC 302 series.
Using a eldbus device reduces system cost, delivers faster
and more ecient communication, and provides an easier
user interface. For ordering numbers, refer to
chapter 13.2 Ordering Numbers for Options and Accessories.
6.1.1
VLT
®
PROFIBUS DP-V1 MCA 101
The VLT
®
PROFIBUS DP-V1 MCA 101 provides:
•
Wide compatibility, a high level of availability,
support for all major PLC vendors, and compati-
bility with future versions.
•
Fast, ecient communication, transparent instal-
lation, advanced diagnosis, and parameterization
and auto-conguration of process data via a GSD
le.
•
Acyclic parameterization using PROFIBUS DP-V1,
PROFIdrive, or Danfoss FC prole state machines.
6.1.2
VLT
®
DeviceNet MCA 104
The VLT
®
DeviceNet MCA 104 provides:
•
Support of the ODVA AC drive prole supported
via I/O instance 20/70 and 21/71 secures compati-
bility to existing systems.
•
Benets from ODVA’s strong conformance testing
policies that ensure products are interoperable.
6.1.3
VLT
®
CAN Open MCA 105
The MCA 105 option provides:
•
Standardized handling.
•
Interoperability.
•
Low cost.
This option is fully equipped with both high-priority access
to control the drive (PDO communication) and to access all
parameters through acyclic data (SDO communication).
For interoperability, the option uses the DSP 402 AC drive
prole.
6.1.4
VLT
®
PROFIBUS Converter MCA 113
The MCA 113 option is a special version of the PROFIBUS
options that emulates the VLT
®
3000 commands in the
VLT
®
AutomationDrive FC 302.
The VLT
®
3000 can be replaced by the VLT
®
AutomationDrive FC 302, or an existing system can be
expanded without costly change of the PLC program. For
upgrade to a
dierent eldbus, the installed converter can
be removed and replaced with a new option. The MCA 113
option secures the investment without losing exibility.
6.1.5
VLT
®
PROFIBUS Converter MCA 114
The MCA 114 option is a special version of the PROFIBUS
options that emulates the VLT
®
5000 commands in the
VLT
®
AutomationDrive FC 302. This option supports DP-V1.
The VLT
®
5000 can be replaced by the VLT
®
AutomationDrive FC 302, or an existing system can be
expanded without costly change of the PLC program. For
upgrade to a
dierent eldbus, the installed converter can
be removed and replaced with a new option. The MCA 114
option secures the investment without losing exibility.
6.1.6
VLT
®
PROFINET MCA 120
The VLT
®
PROFINET MCA 120 combines the highest
performance with the highest degree of openness. The
option is designed so that many of the features from the
VLT
®
PROFIBUS MCA 101 can be reused, minimizing user
eort to migrate PROFINET and securing the investment in
a PLC program.
•
Same PPO types as the VLT
®
PROFIBUS DP V1
MCA 101 for easy migration to PROFINET.
•
Built-in web server for remote diagnosis and
reading out of basic drive parameters.
•
Supports MRP.
•
Supports DP-V1. Diagnostic allows easy, fast, and
standardized handling of warning and fault
information into the PLC, improving bandwidth in
the system.
•
Supports PROFIsafe when combined with VLT
®
Safety Option MCB 152.
•
Implementation in accordance with Conformance
Class B.
Options and Accessories Ove... Design Guide
MG38C202 Danfoss A/S © 01/2018 All rights reserved. 31
6
6