Danfoss VLT AutomationDrive FC 302 - Functional Extensions

6.1.7
VLT
®
EtherNet/IP MCA 121
Ethernet is the future standard for communication at the
factory oor. The VLT
®
EtherNet/IP MCA 121 is based on
the newest technology available for industrial use and
handles even the most demanding requirements.
EtherNet/IP™ extends standard commercial Ethernet to the
Common Industrial Protocol (CIP™) – the same upper-layer
protocol and object model found in DeviceNet.
This option
oers advanced features such as:
•
Built-in, high-performance switch enabling line-
topology, which eliminates the need for external
switches.
•
DLR Ring (from October 2015).
•
Advanced switch and diagnosis functions.
•
Built-in web server.
•
E-mail client for service notication.
•
Unicast and Multicast communication.
6.1.8
VLT
®
Modbus TCP MCA 122
The VLT
®
Modbus TCP MCA 122 connects to Modbus TCP-
based networks. It handles connection intervals down to
5 ms in both directions, positioning it among the fastest
performing Modbus TCP devices in the market. For master
redundancy, it features hot swapping between 2 masters.
Other features include:
•
Built-in web-server for remote diagnosis and
reading out basic drive parameters.
•
Email notication that can be congured to send
an email message to 1 or more recipients when
certain alarms or warnings occur, or when they
are cleared.
•
Dual master PLC connection for redundancy.
6.1.9
VLT
®
POWERLINK MCA 123
The MCA 123 option represents the 2
nd
generation of
eldbus. The high bit rate of industrial Ethernet can now
be used to make the full power of IT technologies used in
the automation world available for the factory world.
This
eldbus option provides high performance, real-time,
and time synchronization features. Due to its CANopen-
based communication models, network management, and
device description model, it oers a fast communication
network and the following features:
•
Dynamic motion control applications.
•
Material handling.
•
Synchronization and positioning applications.
6.1.10
VLT
®
EtherCAT MCA 124
The MCA 124 option oers connectivity to EtherCAT®
based networks via the EtherCAT Protocol.
The option handles the EtherCAT line communication in
full speed, and connection towards the drive with an
interval down to 4 ms in both directions, allowing the MCA
124 to participate in networks ranging from low
performance up to servo applications.
•
EoE Ethernet over EtherCAT support.
•
HTTP (hypertext transfer protocol) for diagnosis
via built-in web server.
•
CoE (CAN over Ethernet) for access to drive
parameters.
•
SMTP (simple mail transfer protocol) for e-mail
notication.
•
TCP/IP for easy access to drive conguration data
from MCT 10.
6.2 Functional Extensions
This section describes the functional extension options that
are available with the VLT
®
AutomationDrive FC 302 series.
For ordering numbers, refer to chapter 13.2 Ordering
Numbers for Options and Accessories.
6.2.1
VLT
®
General Purpose I/O Module
MCB 101
The VLT
®
General Purpose I/O Module MCB 101 oers an
extended number of control inputs and outputs:
•
3 digital inputs 0–24 V: Logic 0 < 5 V; Logic 1 >
10 V.
•
2 analog inputs 0–10 V: Resolution 10 bits plus
sign.
•
2 digital outputs NPN/PNP push-pull.
•
1 analog output 0/4–20 mA.
•
Spring-loaded connection.
6.2.2
VLT
®
Encoder Input MCB 102
The MCB 102 option oers the possibility to connect
various types of incremental and absolute encoders. The
connected encoder can be used for closed-loop speed
control and closed-loop ux motor control.
The following encoder types are supported:
•
5 V TTL (RS 422)
•
1VPP SinCos
•
SSI
Options and Accessories Ove... VLT® AutomationDrive FC 302
32 Danfoss A/S © 01/2018 All rights reserved. MG38C202
6
6