Datalogic PowerScan RF - Page 78

Datalogic PowerScan RF

220 pages

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

72 PowerScan

®

RF Scanner

Disabling

Label ID for a

Specific

Symbology

This procedure is the same as Setting Single Character Label ID above,

except you should scan four zeros before scanning the END bar code.

Table of Contents

Table of Contents3
Introduction7
- Conventions8
  - Scanner Vs. Base Station Features8
Understanding the Basics9
Integrating the Powerscan RF with Your Host System10
- Changing Interfaces10
  - Hardware10
  - Software13
- Customizing Your Scanner's Operation14
Programming Overview15
- Transmit Scanner Configuration to Base Station17
- What Is Programming Mode18
- The Programming Session19
- Programming Sequence20
LED and Beeper Indications22
If You Make a Mistake22
- Return to Factory Settings23
Where to Go from here24
Interface Selection25
- Wand Emulation Interface26
- Wand Emulation Settings27
  - Wand Emulation Pre-/Post-Noise Settings29
- RS-232 Interface/Wn-RS-232 (SNI) Interface31
- RS-232 Communication Parameters32
- Keyboard Wedge Interface44
  - PC Keyboard Wedge Interface Selection45
- Keyboard Wedge Options48
- IBM Interface58
  - Transmit Labels in Code 39 Format59
Label Transmit Configuration (RS-232 and Keyboard Wedge Interfaces Only)61
- Prefix, Suffix, and Label ID62
Symbologies Supported79
- Symbology Overview80
- Symbology Selection82
Symbology Options85
- Code 39/Pharmacode 3985
- Code128 and UCC/EAN 128 Options93
  - Configuring the Code 128/And UCC/EAN 128 Options94
- Interleaved 2 of 5 Options98
  - Configuring the Interleaved 2 of 5 Options100
- Codabar Options107
  - Configuring the Codabar Options109
- UPC/EAN Options119
  - UPC/EAN Options121
- Code 93 Options134
  - Configuring the Code 93 Options135
- Standard 2 of 5/IATA Options138
  - Configuring the Standard 2 of 5 Options140
- Iata146
- Msi/Plessey Options147
  - Configuring the MSI /Plessey Options149
RF Feature Programming155
- Linking the Scanner to a Base Station156
- RF Beeper Settings157
- RF When to Beep158
- Radio Transmit Power164
- RF Channel Selection165
- Transmission Retries before Message Time-Out167
- Wait Time for ACK170
- Wait Time for Scanner Power Shutdown172
- Wait Time between Retries of Failed Transmission173
- HACK Transmit Options175
- Wait Time for HACK from Host177
- Drop Links on Reset Option178
- Drop Oldest Links Option179
- Common Configuration180
- Set Maximum Linked Scanners182
- Source-Radio Identification (ID)184
- Low Battery LED Indication186
General Features187
- Programming the General Features188
Appendix A: Additional Information195
- RS-232 Host Commands195
Technical Support196
- Datalogic Website Support196
- Datalogic Website Tekforum196
- Reseller Technical Support196
- Telephone Technical Support196
Appendix B: Sample Bar Codes197
Appendix C: Keypad199
Appendix D: Record of Programmable Features201
Appendix E: LED and Beeper Indications209

Other manuals for Datalogic PowerScan RF

User Manual88 pages

Related product manuals

Preview: Datalogic PowerScan RF SR

Datalogic PowerScan RF SR

Preview: PowerScan M8300 Readers

PowerScan M8300 Readers

Preview: Datalogic PowerScan D8300

Datalogic PowerScan D8300

Preview: Datalogic PowerScan M8300

Datalogic PowerScan M8300

Preview: Datalogic PowerScan Series

Datalogic PowerScan Series

Preview: Datalogic PowerScan PD9530

Datalogic PowerScan PD9530

Datalogic PowerScan PD8300

Preview: Datalogic PowerScan PM8300

Datalogic PowerScan PM8300

Datalogic PowerScan PM9500

Preview: Datalogic PowerScan PD9600

Datalogic PowerScan PD9600

Datalogic PowerScan CM9630

Preview: Datalogic PowerScan PBT9501

Datalogic PowerScan PBT9501