Dea Spazio 702 S - Display Messages and Error Codes; Error Messages and Solutions

S P A Z I O
Operatinginstructionsandwarnings
16
“OPERATING CONTROL” table
Type of use
Type of control
Informed users
(private areas)
Informed users
(public areas)
Uninformed users
Person-present control Pushbutton control Pushbutton control with key
The person-present control is
not possible
Pulse control with the gate in
sight
Force limitation
or
presence detectors
Force limitation
or
presence detectors
Force limitation
and photocells
or presence detectors
Pulse control with the gate
not in sight
Force limitation
or
presence detectors
Force limitation
and photocells
or presence detectors
Force limitation
and photocells
or presence detectors
Automatic control
(i.e. control with
timed closing)
Force limitation
and photocells
or presence detectors
Force limitation
and photocells
or presence detectors
Force limitation
and photocells
or presence detectors
Messagesshownonthedisplay
Message Description
MESSAGES CONCERNING WORKING STATUS
Closed
Open
Openingunderway
Closingunderway
Whileinstep-by-stepmode,thecontrolboardawaitsfurtherinstructionsafterastartcommand
Stopinputactivated
SICactivatedwhileworkinginbarriermode
ERROR MESSAGES
Message Description Possible solutions
Theypointoutthatthegatehasexceeded:
- (Err1), the max allowed number of reversals (50)
withouteverreachingtothelimitswitch;
- (Err2)the maxnumber ofuninterrupted operations
(10)oftheanti-crushsafetydevice;
Thereforean“emergencymaneuver”isunderway:the
controlboardsetsautomaticallythemotorsinaslow
downphaseandsearchestothelimitswitchinorder
toresetthepositioningsystem.Oncetothelimitswitch
whileclosingarefoundagainthemessagedisappears
andthecontrolboardawaitsfurtherinstructions“----”
andthenresumesworkingnormally.
In case the gate is not properly closed after the emergency maneuver
(maybebecauseoffalsestopsorobstaclesduetomechanicalfrictions),
proceedasfollows:
-Disconnectthepowersupply,checkmanuallythatnoparticularfrictions
and/orobstaclesarepresentduringthecompletestrokeofthedoor/gate.
Leavethedoor/gatehalf-open.
-Connectthepowersupplyagainandsubsequentlygiveastartpulse.At
thispointthedoor/gatewillstarttocloseinslowdownphaseuntilreaching
tothelimitswitch.Makesurethatthemaneuverisproperlycompleted.
Adjustforceandmotorspeedvalues,ifneeded.
Ifthe gate keepsworking inappropriatelytry torepeat themotor stroke
memorizationprocedure
Externalphotocellsand/orsafetydevicesareactivated
oroutoforder
Makesurethatallsafetydevices and/or photocells installed are working
properly.
Themotorisnotconnectedoritsignalscontrolboard
failure
Makesurethatthemotorisproperlyconnected.Ifthemessagereappears
changethecontrolboard.
Voltageofthecontrolboardpowersupplyisbeyond
admittedrange
Ensurepowersupplyvoltageonfastonconnections1-2isequivalentto22V
+/-10%andonfastonconnection3-4isequivalentto27V +/-10%.
Themotorisprobablyoverheatedbecausesomething
hindersthedoortravelrange.
Thecontrolboarddoesnotreacttocommands
Remove any obstacle and wait until message “bLOC” replaces message
“Err6”forthecontrolboardtoresumeacceptinginstructions(afewseconds).