DeLonghi ECAM23.46X - Descaling Menu Option; Filter Installation;Replacement; Time Adjustment; Auto-start Configuration

11
• press the main switch (A8) (g. 2).
Important!
Never press the main switch while the appliance is on.
8. MENU SETTINGS
When you access the settings menu by pressing the P button
(B4), the following menu items can be selected:
8.1 Descaling
For instructions on descaling, see section “14. Descaling”.
8.2 Install lter
For instructions on how to install the lter (C4), see section “16.1
Installing the lter”.
8.3 Replacing the lter
For instructions on how to replace the lter (C4), see section
“16.2 Replacing the lter”.
8.4 Adjust time
To adjust the time on the display (B1), proceed as follows:
1. Press the P button (B4) to enter the menu;
2. Turn the selection dial (B2) (g. 7) until "Adjust time" is
displayed;
3. Press the button (B9) (g. 3);
4. Turn the selection dial (g. 7) to change the hours;
5. Press the button to conrm;
6. Turn the selection dial (g. 7) to change the minutes;
7. Press the button to conrm.
The time is set: press the button (B5) to exit the menu.
8.5 Auto-start
You can set the auto-start time in order to have the appliance
ready at a certain time (for example in the morning) so you can
make coee immediately.
Please note:
To enable this function, the time must already be set correctly.
To enable auto-start, proceed as follows:
1. Press the P button (B4) to enter the menu;
2. Turn the selection dial (B2) (g. 7) until "Auto-start" ap-
pears on the display (B1);
3. Press the button (B9). "Enable?" appears on the
display;
4. Press the button to conrm;
5. Turn the selection dial to choose the hours;
6. Press the button to conrm;
7. Turn the selection dial (g. 7) to change the minutes;
8. Press the button to conrm;
9. Press the button (B5) to exit the menu.
Once the time has been conrmed, activation of auto-start is
indicated by the symbol displayed alongside the time and
under "Auto-start" in the menu.
To disable the function:
1. Select auto-start from the menu;
2. Press the button. "Disable?" is displayed;
3. Press the button to conrm.
The symbol is no longer displayed.
8.6 Auto-o
The time can be changed so that the appliance switches o after
15 or 30 minutes, or after 1, 2 or 3 hours.
To re-programme Auto-o, proceed as follows:
1. Press the P button (B4) to enter the menu;
2. Turn the selection dial (B2) (g. 7) until "Auto-o" appears
on the display (B1);
3. Press the button (B9);
4. Turn the selection dial (g. 6) until the required operating
time (15 or 30 minutes, or 1, 2 or 3 hours) is displayed;
5. Press the button to conrm;
6. Press the button (B5) to exit the menu.
Auto-o is now programmed.
8.7 Energy saving
Use this function to enable or disable energy saving. When en-
abled, the function reduces energy consumption in compliance
with European regulations.
When energy saving mode is active, an asterisk appears under
"Energy Saving" in the menu.
To enable or disable energy saving, proceed as follows:
1. Press the P button (B4) to enter the menu;
2. Turn the selection dial (B2) (g. 7) until "En-
ergy Saving" appears on the display (B1);
3. Press the button (B9). "Disable?" is displayed (or
"Enable?" if the function has already been disabled);
4. Press the button to disable energy saving mode;
5. Press the button (B5) to exit the menu.
When the function is active, if the machine is not used for some
time, "Energy saving" is displayed.
Please note!
• When in energy saving mode, a few seconds elapse before
the rst coee, cappuccino or milk-based drink is delivered
as the appliance must heat up again.
• To prepare any drink, press any button to exit energy sav-
ing, then press the button corresponding to the drink you
want to make.