DeLonghi ECAM23.46X - Initial Rinse Recommendation; Customizing My Coffee Quantity; Coffee Grinder Adjustment; Tips for Hotter Coffee

13
Important! Danger of burns.
Do not leave the appliance unattended while hot water is being
delivered.
1) To enable this function, press the button (B5).
"RINSING, Please wait" appears on the display (B1);
2) After a few seconds, hot water is delivered rst from the
coee spouts, then from the hot water spout (if inserted)
to clean and heat the appliance’s internal circuit. "RINSING"
appears on the display, together with a progress bar which
lls gradually as preparation proceeds;
3) To stop the process press any button or wait for delivery of
water to stop automatically.
Please note!
• If the appliance is not used for more than 3-4 days, when
switched on again, we strongly recommend performing
2/3 rinses before use;
• After cleaning, it is normal for the coee grounds container
(A14) to contain water.
10. MAKING COFFEE
10.1 Selecting the coee taste
The appliance is set by default to make coee with a standard
taste.
You can also choose one of these tastes:
Extra-mild taste
Mild taste
Standard taste
Strong taste
Extra-strong taste
To change the taste, press the aroma selection button
(B6) (g. 8) repeatedly until the required taste appears on the
display (B1).
10.2 Selecting the quantity of coee in the cup
The appliance is set by default to make a standard quantity of
coee. To select the quantity of coee, turn the selection dial
(B2) (g. 7) until the message corresponding to the required
quantity of coee appears on the display (B1):
Coee selected Quantity in cup (ml)
MY COFFEE Programmable:
from ≃20 to ≃180
SHORT
≃40
STANDARD
≃60
LONG
≃90
EXTRA LONG
≃120
10.3 Customising the "my coee" quantity
The appliance is set by default to automatically deliver 30ml of
"my coee". To modify this quantity, proceed as follows:
1. Place a cup under the coee spouts (A14) (g. 9);
2. Turn the selection dial (B2) (g. 7) until "MY COFFEE" is
displayed;
3. Press and hold the button (B7) (g. 10) until the
message "1 MY COFFEE Program quantity" appears on the
display (B1) and coee delivery begins. Then release the
button;
4. As soon as the coee in the cup reaches the required level,
press the button (g. 10) again.
The quantity of coee in the cup has now been programmed.
10.4 Adjusting the coee mill
The coee mill is set by default to prepare coee correctly and
should not require regulating initially.
However, if after making the rst few coees you nd that the
coee is either too weak and not creamy enough or delivery is
too slow (a drop at a time), this can be corrected by adjusting
the grinding adjustment dial (A2) (g. 11).
Please note:
The grinding adjustment dial must only be turned when the
coee mill is in operation.
If the coee is delivered too slowly or
not at all, turn one click clockwise to-
wards 7.
For fuller bodied creamier coee, turn
one click anticlockwise towards 1 (do
not turn more than one click at a time
otherwise the coee could be deliv-
ered a drop at a time).
These adjustments will only be evident after at least 2 cups of
coee have been delivered. If this adjustment does not obtain
the desired result, turn the dial another click.
10.5 Tips for a hotter coee
For hotter coee, you should:
• perform a rinse cycle before delivery by pressing the
button (B5), as described in section “10. making coee”;
• warm the cups with hot water using the hot water function
(see section “12. Hot water”);
• select the "high" coee temperature in the menu (see sec-
tion “8.8 Setting the temperature”).