DEMA 633AG-1 - Page 2

DEMA 633AG-1 & 633AG-4 BLEND CENTER
INSTALLATION INSTRUCTIONS
I-459 Pg. 2 of 6
Rev. F-42084 9/8/16
TABLE 1 - 164BAG (1 GPM FLOW RATE PROPORTIONER - 1/4" BARB AND TUBING)
Metering Tip
Color
Injection Rates For Viscosities Shown
1 cps
75 cps
200 cps
Oz/Gal
Ratio
Oz/Gal
Ratio
Oz/Gal
Ratio
Tan
1.25
102-1
0.90
142-1
0.60
213-1
Orange
1.70
75-1
1.20
107-1
0.80
160-1
Turquoise
2.15
60-1
1.55
83-1
1.10
116-1
Pink
3.00
43-1
2.00
64-1
1.50
85-1
Light Blue*
3.90
33-1
2.75
47-1
1.80
71-1
Brown
4.55
28-1
3.00
43-1
2.00
64-1
Red
5.80
22-1
3.60
36-1
2.30
56-1
White
7.00
18-1
4.45
29-1
2.70
47-1
Green
7.90
16-1
5.00
26-1
3.00
43-1
Blue
9.80
13-1
5.75
22-1
3.30
39-1
Yellow
14.80
9-1
7.35
17-1
3.55
36-1
Black
20.15
6-1
8.50
15-1
3.70
35-1
Purple
27.80
5-1
9.80
13-1
3.80
34-1
Gray
31.60
4-1
10.50
12-1
3.90
33-1
No Tip
35.70
3.6-1
11.80
11-1
4.50
28-1
*Metering tip color was formerly clear. Note: All induction rates are base on a water pressure of 40 psi.
Leaner dilutions can be achieved by ordering DEMA ultra lean tip kit 100-15KU.
TABLE 2 - 164AG (1 GPM FLOW RATE PROPORTIONER - 3/8" BARB AND TUBING)
Metering Tip
Color
Injection Rates For Viscosities Shown
1 cps
75 cps
200 cps
Oz/Gal
Ratio
Oz/Gal
Ratio
Oz/Gal
Ratio
Clear
1.40
91-1
1.00
128-1
0.85
151-1
Purple
2.15
60-1
1.75
73-1
1.40
91-1
Yellow
4.00
32-1
3.25
39-1
2.80
46-1
Green
6.70
19-1
5.40
24-1
4.50
28-1
Pink
8.70
15-1
7.00
18-1
5.60
23-1
Turquoise
14.15
9-1
11.15
11-1
8.15
16-1
Black
17.25
7-1
13.50
9-1
10.00
13-1
Gray
22.60
6-1
16.75
8-1
11.60
11-1
Red
25.15
5-1
19.50
7-1
13.50
10-1
Blue
27.50
4.7-1
21.65
6-1
14.25
9-1
Brown
31.00
4-1
24.25
5-1
15.60
8-1
White
33.50
3.8-1
26.25
4.9-1
16.70
7.7-1
Orange
35.40
3.6-1
28.00
4.6-1
17.40
7.4-1
Lt. Blue*
36.50
3.5-1
29.00
4.4-1
18.20
7-1
Tan*
37.80
3.4-1
29.90
4.3-1
18.65
6.9-1
No Tip
38.30
3.3-1
30.90
4.1-1
21.30
6-1
Note: All induction rates are base on a water pressure of 40 psi. *These tips are not included in standard tip kit