Measures
Cause
Screen example
11
ENGLISH
Easy Setup and Operation Easy Setup and Operation
ENGLISH
Check of the measurement result
The results of the measured items can be checked.
1
Press the CURSOR
DD
or
HH
button to
select the items, then press the
ENTER
button.
• Switch to the verification screen.
2
Press the ENTER button.
• Switch to the second screen.
[ First screen ]
[ Second screen ]
3
If the check ends, press the ENTER
button again.
• Sometimes due to the electrical complexities of
subwoofers and the interaction with the room, THX
recommends setting the level and the distance of
the subwoofer manually.
• Sometimes due to interaction with the room, you
may notice irregular results when setting the level
and/or distance of the main speakers. If this
happens, THX recommends setting them manually.
• Please note that any THX main speakers should be
set to Small (80 Hz). If you set up your speakers
using Auto Setup, please make sure manually that
any THX speakers are set to Small with 80 Hz
crossover.
NOTE:
• Do not turn off the power while the data is being
stored. If the power is turned off while the data
is being stored, the Room EQ parameters stored
in the memory will be cleared, and it will not be
possible to select the “Audyssey”, “Front” or
“Flat” equalizer settings.
5
Press the CURSOR
FF
button.
• After the data is stored, the “Auto Setup /
Room EQ” menu screen appears
automatically.
Example: Speaker Config. Check
• When measurements have been made using the
measurement microphone, speakers with a built-in
filter such as subwoofers might be set with a value
that differs from the physical distance because of
the internal electrical delay.
About the error message
These error messages will be displayed when
performing the measurements of Auto Setup and the
automatic measurements can not be completed
because of the speaker arrangement, measurement
environment, or other factors. Please check the
following matters, reset the pertinent items, and
measure again. Be sure to turn off the AVC-A11XV’s
power before checking the speaker connections.
q The speakers required for producing
suitable reproduction have not been
detected.
• The front L and front R speakers were not
properly detected.
• Only one channel of the surround (A) and
surround (B) speakers was detected.
• Sound was output from the R channel
when only one surround back speaker was
connected.
• The surround back or the surround (B)
speaker was detected, but the surround
(A) speaker was not detected.
If multiple errors occur, press the CURSOR
FF
or
GG
button to check the contents.
•Check that the pertinent speakers
are properly connected.
w The speaker polarity is connected in
reverse.
If multiple errors occur, press the CURSOR
FF
or
GG
button to check the contents.
• Check the polarity of the
pertinent speakers.
• For some speakers, the screen
below may be displayed even
though the speakers are properly
connected.
If so, select “Skip
0
”.
e There is too much ambient noise in the
room and the measurements cannot be
made accurately.
r The sound level that is output from the
speakers and/or subwoofer is too low.
• Either turn off the power of the
device that generated the noise
during the measurements or
move the device away.
•Try again at a time when it is
quieter.
• Check the placement and
orientation of the loudspeakers.
• Adjust the subwoofer’s output
level.
t The measurement microphone is not
connected, or all of speakers have not
been detected.
• Connect the measurement
microphone to the microphone
connector.
• Check the speaker connection.
Playing a DVD with surround sound
1
Disconnect the microphone from the
unit.
2
Select the input source to be played.
3
Select the play mode.
4
5
Adjust the volume.
Start DVD playback.
Store:
Set with the checked measurement value.
All parameters are stored up.
Cancel:
Cancel the auto setup settings.
4
Press the CURSOR
DD
or
HH
button to
select whether or not to save the data
you have checked.
Example: Speaker Config. Check
To Next Page
Loading...
