Denon AVC-A11XV - SURROUND ch

ENGLISH
ENGLISH
12
Cable indications
Signal direction
Audio and Video cable
The hookup diagrams on the subsequent pages assume the use of the following optional connection cables (not
supplied).
Video cableAudio cable
NOTE:
• Do not plug in the Power supply cord until all connections have been completed.
• When making connections, also refer to the operating instructions of the other components.
• Be sure to connect the left and right channels properly (left with left, right with right).
• Note that binding pin-plug cables together with Power supply cords or placing them near a power
transformer will result in generating hum or other noise.
Analog terminal (Stereo)
A
R
L
R
L
(Orange)
Pin-plug cable
Analog terminal (Monaural, for subwoofer)
B
Pin-plug cable
Digital terminal (Coaxial)
C
Coaxial cable (75 Ω/ohms pin-plug cable)
Digital terminal (Optical)
D
Optical cable (Optical fiber cable)
DENON LINK terminal
E
DENON LINK cable
IEEE1394 terminal
F
4-pin, S400 IEEE1394 cable
Speaker terminal
G
Speaker cable
Video terminal
H
Video cable (75 Ω/ohms video pin-plug cable)
S video terminal
I
S video cable
DVI-D terminal
K
24-pin DVI-D cable
HDMI terminal
L
HDMI cable
(Yellow)
Audio signal
Video signal
(White)
(Red)
Component video terminal
J
Component video cable
(Y)
(P
B/CB
)
(P
R/CR)
(Green)
(Blue)
(Red)
IN OUT OUT IN
IN OUT OUT IN
The AVC-A11XV is equipped with a function for up and
down converting video signals.
Because of this, the AVC-A11XV’s MONITOR OUT
terminal can be connected to the monitor (TV) with a
set of cables offering a higher quality connection,
regardless of how the player and the AVC-A11XV’s
video input terminals are connected.
Generally speaking, analog video connections using
the component video terminals offer the highest
quality playback, followed by connections using the S-
Video terminals, then connections using the regular
video terminals (yellow).
The flow of the video signals.
This unit’s
input terminals
This unit’s output
terminals
(Component
Video terminals)
(S-Video terminal)
(Video terminal)
The video conversion function
2 The analog video to HDMI
conversion function:
• The AVC-A11XV’s video up-conversion function lets
you output analog video input signals (component –
480i/576i, 480p/576p, 1080i or 720p; S-Video and
composite video - 480i/576i) to the HDMI monitor
output terminal with the original resolution.
•The on screen display signals are output from the
HDMI monitor output terminal with a resolution of
480i/576i. Because of this, if the monitor equipped
with HDMI terminal is compatible with the 480i/576i
resolution, all the signals the AVC-A11XV handles
can be output to the monitor with a single HDMI
cable. The resolutions with which the monitor is
compatible can be checked using the STATUS button
on the main unit or the ON SCREEN button on the
remote control unit.
(HDMI / DVI-D
terminals)
: only MAIN ZONE 480i/576i
NOTE:
• It is not possible to down-convert from HDMI and
DVI-D input signals to the component, S-Video or
composite video monitor output terminals.
•Video down conversion to the MAIN ZONE’s
monitor output is only possible when the
component video input resolution is 480i
(interlaced standard definition video – NTSC
format, for North America) or 576i (interlaced
standard definition video – PAL format, for Europe
and other countries).
•To change the setting of the video conversion
mode for the MAIN ZONE ( page 45).
Connecting Other Sources
(HDMI
terminal)
(Component
Video terminals)
(S-Video terminal)
(Video terminal)
Connecting Other Sources
•If the monitor equipped with HDMI terminal is not
compatible with the 480i/576i resolution, connect
the player and the AVC-A11XV using a component
cable and set the player’s resolution to one which
the monitor can handle.
• If you do not want to use the function for converting
analog video signals to HDMI signals, select “OFF”
for “Analog to HDMI Convert” at “Setting the HDMI
Out Setup”( page 46).
In this case, the function for video up conversion to
the component video terminal operates.
NOTE:
• Connecting a LD (laser disc) player with a Dolby Digital RF Output.
The AVC-A11XV does not have a DD RF demodulator function. Therefore, you need to use a commercially
available outboard DD RF demodulator and connect its digital output to one of the AVC-A11XV available
digital inputs. Refer to the demodulator’s owner’s manual for further information.