21
ENGLISH
Basic Operation Basic Operation
Playback using the external input
(EXT. IN) terminals
Press the EXT. IN button to switch the
external input.
NOTE:
• When the input mode is set to the external input
(EXT. IN), the surround mode (DIRECT, STEREO,
HOME THX CINEMA, STANDARD, 7CH
STEREO, WIDE SCREEN or DSP SIMULATION)
cannot be set.
• In play modes other than the external input
mode, the signals connected to these terminals
cannot be played. In addition, signals cannot be
output from channels not connected to the input
terminals.
Press the MUTING button.
•You can adjust the muting level ( page 50).
Turning the sound off temporarily
(MUTING)
Use this to mute the audio output temporarily.
Connect the headphone to the PHONES jack.
• The pre-out output (including the speaker output) is
automatically turned off when headphones are
connected.
NOTE:
•To prevent hearing loss, be careful not to raise
the volume level excessively when using
headphones.
Listening over headphone
EXT. IN
ANALOG
INPUT MODE
PHONES
STATUS
VOLUMEDIMMER
INPUT MODE
VIDEO SELECT
ANALOG
VOLUME
EXT. IN
MUTING
ON SCREEN
SPEAKER
• Cancelling the external input mode:
Press the INPUT MODE or ANALOG button to switch to
the desired input mode ( page 21, 22).
• The external input mode can be set for any input
source. To watch video while listening to sound,
select the input source to which the video signal is
connected, then set this mode.
• If the subwoofer output level seems too high, set
the “SW ATT” surround parameter to “ON”.
• Cancelling MUTING mode:
Press the MUTING button again, or press the VOLUME
button on the remote control, or adjust the volume
up or down via the front panel VOLUME knob.
Press the ON SCREEN button.
Each time an operation is performed, a
description of that operation appears on the
display connected to AVC-A11XV’s VIDEO
MONITOR OUT terminal. Also, the unit’s
operating status can be checked during playback.
Such information as the position of the input
selector and the surround settings is output in
sequence.
Checking the currently playing
program source, etc.
2 On screen display
Input mode
The AVC-A11XV has an AUTO signal detection mode
that automatically identifies the type of incoming audio
signals, but is also equipped with a manual mode that
can be switched according to the type of input audio
signals.
Press the INPUT MODE button.
The mode switches as shown below each time
the INPUT MODE button is pressed.
2 Selecting the AUTO, PCM and DTS
modes
AUTO: (All auto mode)
In this mode, the types of signals being input to
the digital and analog input terminals for the
selected input source are detected and the
program in the AVC-A11XV’s surround decoder is
selected automatically upon playback. This mode
can be selected for all input sources other than
PHONO.
The presence or absence of digital signals is
detected, the signals input to the digital input
terminals are identified and decoding and playback
are performed automatically in DTS, Dolby Digital
or PCM (2 channel stereo) format. If no digital
signal is being input, the analog input terminals are
selected.
Use this mode to play Dolby Digital signals.
Press the VIDEO SELECT button until the
desired image appears.
Combining the currently playing
sound with the desired image
(VIDEO SELECT)
The video source selected with the video select
function is stored in the memory for the different
input sources.
Switching the surround speakers
Press the SPEAKER button.
The surround speakers switch as shown below
each time the SPEAKER button is pressed.
SURROUND A
SURROUND A+B
SURROUND B
This operation is possible when the setting for
using both surround speakers A and B is made at
“Setting the type of speakers” ( page 53).
Press the DIMMER button.
The display brightness changes in four steps
(bright, medium, dim and off).
2 Using the dimmer function
Use this to change the brightness of the display.
Press the STATUS button.
Descriptions of the unit’s operations are also
displayed on the front panel display. In addition,
the display can be switched to check the unit’s
operating status while playing a source.
2 Front panel display
• Cancelling simulcast playback:
Select the “SOURCE” pressing the VIDEO SELECT
button.
• It is not possible to select HDMI and DVI-D input
signals.
ENGLISH
To Next Page
Loading...
