Denon AVC-A11XV - Page 30

ENGLISH
27
ENGLISH
Basic Operation Basic Operation
Dolby Pro Logic
II
x
(Pro Logic
II
) mode
•To play in the PLII x mode, set “Sp.Back” at the
Speaker Configuration setting to “1spkr” or
“2spkrs”.
•To play in the PL
IIx mode, set “Surround Back” at
the Power Amp Assign setting.
1
Press the STANDARD button to select
the “Dolby Pro Logic
IIx” mode.
• The Dolby Pro Logic indicator lights.
light
DTS NEO:6DOLBY PL IIx
3
Press the SURROUND PARAMETER
button.
• Display the surround parameter menu.
2
Play a program source
with the mark.
4
Press the CURSOR
FF
or
GG
button to
select the play mode.
Display
MODE: PL x C
*Surr Parameter
MODE: PL x M
*Surr Parameter
MODE: PL x G
*Surr Parameter
(Pro Logic IIx Cinema
mode)
(Pro Logic
IIx Music
mode)
(Pro Logic IIx Game
mode)
When the “SB CH OUT” parameter is set to
“OFF”. (Set “SP.Back” at the System Setup to
“None”).
Display
MODE: PL C
*Surr Parameter
MODE: PL M
*Surr Parameter
MODE: PL G
*Surr Parameter
*Surr Parameter
MODE: DOLBY PL
(Pro Logic II Cinema
mode)
(Pro Logic II Music
mode)
(Pro Logic
II Game
mode)
(Dolby Pro Logic
mode)
The mode switches as shown below each time
the STANDARD button is pressed.
For operating instructions, refer to the manuals
of the respective components.
When the “SB CH OUT” parameter is set to
“ON”. (Set “SP.Back” at the System Setup to
“1spkr” or “2spkrs”).
When set with the on screen display using the
remote control unit while in the MUSIC mode,
set the “ ” mark to “OPTIONS
0” pressing
the CURSOR
DD
or
HH
button, then press the
CURSOR
FF
button.
Press the ENTER button to return to the previous
screen.
6
Press the CURSOR
FF
or
GG
button to
adjust the parameters setting.
7
Press the ENTER or SURROUND
PARAMETER
button to complete the
setting.
5
Press the CURSOR
DD
or
HH
button to
select the various surround parameters.
SURROUND
PARAMETER
STANDARD
ENTER
CURSOR
STANDARD
SURROUND
SURROUND
PARAMETER
ENTER
CURSOR
2 Surround parameters r
Pro Logic IIx and Pro Logic II Mode:
Select one of the modes (“Cinema”, “Music”, “Pro
Logic” or “Game”).
The Cinema mode is for use with stereo television
shows and all programs encoded in Dolby Surround.
The Music mode is recommended for stereo music
and surround-encoded stereo music sources.
The Pro Logic mode emulates Dolby Laboratories’
original Dolby Pro Logic surround decoding, and may
provide better results with older, legacy surround-
encoded program material.
The Game mode is optimized for computer and/or
dedicated game box consoles, that feature stereo
analog or digital outputs. It can only be used with 2-
channel stereo sources.
PANORAMA:
This mode extends the front stereo image to include
the surround speakers for an exciting “wraparound”
effect with side wall imaging.
Select “OFF” or “ON”.
DIMENSION:
This control gradually adjust the soundfield either
towards the front or towards the rear.
The control can be set in 7 steps from 0 to 6.
CENTER WIDTH:
This control adjust the center image so it may be
heard only from the center speaker; only from the
left/right speakers as a phantom image; or from all
three front speakers to varying degrees.
The control can be set in 8 steps from 0 to 7.
Example:
DOLBY PL
IIx music mode screen
Press the CURSOR
FF
button to select
“Default Yes
00
”, then parameters set to
default setting.
• There are four Dolby Surround Pro Logic modes
(NORMAL, PHANTOM, WIDE and 3 STEREO). The
AVC-A11XV sets the mode automatically according
to the types of speakers set during the system setup
process ( page 53).
DEFAULT setting: