Denon AVC-A11XV - DTS NEO:6 Mode; The Dolby Headphone

ENGLISH
ENGLISH
Basic Operation Basic Operation
28
DTS NEO:6 mode
Surround playback can be performed for the analog
input and digital input 2-channel signals.
1
Press the STANDARD button to select
the “DTS NEO:6” mode.
• The DTS NEO:6 indicator lights.
light
DTS NEO:6DOLBY PL IIx
Play a program source.
3
Press the SURROUND PARAMETER
button.
•Display the surround parameter menu.
5
Press the CURSOR
DD
or
HH
button to
select the various surround parameters.
7
Press the ENTER or SURROUND
PARAMETER
button to complete the
setting.
6
Press the CURSOR
FF
or
GG
button to
adjust the parameters setting.
4
Press the CURSOR
FF
or
GG
button to
select the play mode.
2 Surround parameters t
DTS NEO:6 Mode:
• Cinema:
This mode is optimum for playing movies. Decoding
is performed with emphasis on separation
performance to achieve the same atmosphere with
2-channel sources as with 6.1-channel sources.
This mode is effective for playing sources recorded
in conventional surround formats as well, because
the in-phase component is assigned mainly to the
center channel (C) and the reversed phase
component to the surround (SL, SR and SB
channels).
• Music:
This mode is suited mainly for playing music. The
front channel (FL and FR) signals bypass the decoder
and are played directly so there is no loss of sound
quality, and the effect of the surround signals output
from the center (C) and surround (SL, SR and SB)
channels add a natural sense of expansion to the
sound field.
CENTER IMAGE (0.0 to 1.0: default 0.3):
The center image parameter for adjusting the
expansion of the center channel in the DTS NEO:6
MUSIC mode has been added.
SURROUND
PARAMETER
ENTER STANDARD
CURSORPHONES
SURROUND
SURROUND
PARAMETER
ENTER
STANDARD
CURSOR
The Dolby Headphone
The Dolby Headphone mode is set when headphones
are connected to the PHONES jack while in the
DOLBY/DTS SURROUND mode.
1
Press the SURROUND PARAMETER
button.
• Display the surround parameter menu.
2
Press the CURSOR
DD
or
HH
button to
select the parameter.
3
Press the CURSOR
FF
or
GG
button to
select the setting.
4
Press the ENTER or SURROUND
PARAMETER
button to complete the
setting.
2 Parameters
MODE:
• DH1:
Reference room (small room with weak
reverberations).
• DH2:
Live room (room with a bit stronger reverberations
than DH1).
• DH3:
Large room (larger room than DH1, offers a sense of
distance and sound diffusion effects).
• BYPASS:
Stereo sound.
DECODER:
Select this when playing analog, PCM or other 2-
channel sources.
The signals are converted into multichannel signals
using the decoders shown below and played in the
Dolby Headphone mode.
• PL
II C:
Dolby Pro Logic
II Cinema mode.
• PL
II M:
Dolby Pro Logic
II Music mode.
• NEO:6 C:
DTS NEO:6 Cinema mode.
• NEO:6 M:
DTS NEO:6 Music mode.
• OFF:
The signals are played in the Dolby Headphone
mode as such (2 channels).
– Recording –
When RECOUT mode is set to “SOURCE”, with this
amplifier signals encoded in the Dolby Headphone
mode can be output from the recording output
terminals and recorded on another recorder (
page 40).
The mode switches as shown below each time
the STANDARD button is pressed.
2
• When “Default” is selected and the CURSOR
FF
button is pressed, “MODE” and “TONE” are
automatically reset to the default values and
“CINEMA EQ.” is set to “OFF”.
• When playing PCM digital signals or analog signals in
the DOLBY PRO LOGIC
II, DOLBY PRO LOGIC II x,
DTS NEO:6 modes and the input signal switches to
a digital signal encoded in Dolby Digital, the Dolby
surround mode switches automatically. When the
input signal switches to a DTS signal, the mode
automatically switches to DTS surround.