36
ENGLISH
Advanced Operation Advanced Operation
ENGLISH
2 Storing system call signals
1
Press the ON and OFF button at the
same time.
2
Press the 3 button to select system call
setting.
3
Press the MODE SELECTOR button for
the component you want to register at
the
SYSTEM CALL button, then press
the
ENTER button.
4
Press the button you want to register.
5
Repeat steps 4 to register the desired
buttons.
6
Press the ENTER button after the button
registration is completed.
• There will be a changeover to the system call
registration screen.
7
Press buttons from SYSTEM CALL 1 to
6 to register the system call.
• “OK” is displayed and the set returns to the
normal operating mode.
2 Using the system call function
NOTE:
• The remote control signals of the buttons
pressed while registering the system call signals
are emitted, so be careful not to operate the
components accidentally (cover the remote
sensors, for example).
Press the button at which the system call
signals have been stored.
• The stored signals are transmitted successively.
Punch through
Buttons used in the CD, CDR, DVD, DVDR, VDP,
VCR1 and VCR2 modes can be assigned to the
buttons which are not normally used in the AMP,
ZONE2, ZONE3, ZONE4, TV and DBS modes.
For example, when the CD mode is set to the punch
through mode in the AMP mode, the CD mode’s PLAY,
STOP, MANUAL SEARCH, AUTO SEARCH and PAUSE
buttons’ signals are sent in the AMP mode. ( )
1
Press the ON and OFF button at the
same time.
2
Press the 4 button to select punch
through setting.
3
Press the MODE SELECTOR button for
the component you want to make the
punch through setting, then press the
ENTER button.
4
Press the MODE SELECTOR button for
the component you want to punch
through, then press the
ENTER button.
• The punch through is set and the set returns
to the normal operating mode.
Setting the back light’s lighting time
1
Press the ON and OFF button at the
same time.
2
Press the 5 button to select Light setup.
3
Press the button you want to adjust the
lighting time (5 sec ~ 20 sec).
Setting the brightness
Hold the ENTER button and press the
CHANNEL + button.
The brightness of the display can be adjusted in 3
levels.
2 For 1 brightness step increase
2 For 1 brightness step decrease
Hold the ENTER button and press the
CHANNEL – button.
Resetting
2 Resetting the preset memory
1
Press the ON and OFF button at the
same time.
2
Press the 6 button to select resetting.
3
Press the 1 button to resetting the preset
memory.
4
Press the MODE SELECTOR button you
want to resetting, then press the
ENTER
button.
• The set returns to the normal operating
mode.
2 Resetting the learned buttons
1
Press the ON and OFF button at the
same time.
2
Press the 6 button to select resetting.
3
Press the 2 button to resetting the
learned buttons.
• The MODE SELECTOR buttons will all light.
4
Press the MODE SELECTOR button you
want to resetting, then press the
ENTER
button.
• The set returns to the normal operating
mode.
The mode can be switched by pressing a MODE
SELECTOR button.
Up to 12 signals each can be stored at the
SYSTEM CALL 1 ~ 6.
• If you exceed the number of signals that can be
registered, there will be a changeover to the system
call registration screen.
2 Lighting time
1:5 sec
2:10 sec (factory default)
3:15 sec
4:20 sec
2 Resetting List
1:Resetting the preset memory
2:Resetting the “Learned” buttons
3:Resetting the system call
4:Resetting the punch through setting
+10 : All reset function (factory default)
• The MODE SELECTOR buttons that were set in
preset memory will all light.
To Next Page
Loading...
