40
ENGLISH
Advanced Operation Advanced Operation
ENGLISH
2 Recording Dolby Digital and DTS
multi channel sources
•With this set it is possible to record Dolby Digital and
DTS multichannel signals converted into 2-channel
analog signals.
• The recording signals are output to the TAPE and
VCR output terminals.
• Down-mixed analog signals converted into digital
signals are output from the OPTICAL 2, 3 and 4
digital output terminals at this time.
1
Press the ZONE3/REC SELECT button
until “RECOUT SOURCE” appears on
the display.
2
Press the INPUT MODE button to set
the input mode according to the source
to be played.
3
Press the DIRECT/STEREO button to set
the surround mode.
• The multichannel digital signals are down-
mixed and output to the TAPE and VCR
output terminals.
4
Set the recording mode.
Initialization of the microprocessor
In very rare instances, the AVC-A11XV internal
microprocessor might lock up, or otherwise cause
mis-operation. This might be caused due to an AC line
surge or line spike noise, or by static electric discharge
on or nearby the unit, or to connected components. If
the condition cannot be corrected by powering off the
unit, including disconnection of the Power supply cord
for a period of ten minutes and subsequent re-
connection, then the unit may have to be re-initialized.
Doing so will restore the microprocessor to its original
out-of-the-box state, with all custom memories and
settings erased, and the original factory default
settings restored. Only use this procedure if you are
sure that the microprocessor requires re-initialization.
1
Switch off the unit using the main unit’s
POWER switch.
2
Hold the following PURE DIRECT
button and DIRECT/STEREO button,
and turn the main unit’s
POWER switch
on.
3
Check that the entire display is flashing
with an interval of about 1 second, and
release your fingers from the 2 buttons.
• The microprocessor will be initialized.
1
The Dolby Headphone play mode is set
when headphones are connected to the
PHONES jack during playback in the
DOLBY/DTS surround mode.
• When this is done, signals encoded in the
Dolby Headphone mode are automatically
output from the recording output terminals
(analog and digital) and can be recorded.
2
Select the parameters and set the
desired mode.
• Start recording.
NOTE:
• Do not disconnect the headphones during
recording.
2 Dolby Headphone recording
When REC OUT mode is set to “SOURCE”, with the
AVC-A11XV it is possible to output signals encoded in
the Dolby Headphone mode from the recording output
terminal and record them on a separate recorder.
Last function memory
• This unit is equipped with a last function memory
which stores the input and output setting conditions
as they were immediately before the power is
switched off.
This function eliminates the need to perform
complicated resetting when the power is switched
on.
• The unit is also equipped with a back-up memory.
This function provides approximately one week of
memory storage from when the main unit’s power
switch is off and with the power supply cord
disconnected.
•To cancel, turn the FUNCTION knob and select
“SOURCE”.
• Recording sources other than digital inputs selected
in the REC OUT mode are also output to the ZONE3
audio/video output terminals.
• When the REC OUT mode is selected, the ZONE3
button on the remote control unit cannot be
operated.
• When “ZONE2 SELECT” is selected at “Digital Out
Assign”, the source switches in association with the
“ZONE2 SELECT” mode for the OPTICAL2 OUT
connector ( page 52).
Refer to the “The Dolby Headphone” ( page
28).
• If step 3 does not work, start over from step 1.
• If the microprocessor has been reset, all the settings
are reset to the default values (the values set upon
shipment from the factory).
Multi-source recording / playback
1
Press the ZONE3/REC SELECT button
until “RECOUT SOURCE” appears on
the display.
• The “REC” indicator lights.
2
Turn the FUNCTION knob to select the
source you wish to record.
3
Set the recording mode.
To Next Page
Loading...
