42
ENGLISH
Advanced Setup – Part 1 Advanced Setup – Part 1
ENGLISH
Setting the Digital In Assignment
This setting assigns the digital input terminals of the
AVC-A11XV for the different input sources.
1
Press the CURSOR
DD
or
HH
button to
select the “Audio Input Setup” at the
“System Setup Menu”, then press the
ENTER button.
• Display the “Audio Input Setup” menu
screen.
2
Press the CURSOR
DD
or
HH
button to
select the “Digital In Assign” at the
“Audio Input Setup” menu, then press
the
ENTER button
• Display the “Digital In Assign” screen.
3
Press the CURSOR
DD
or
HH
button to
select the input source, then press the
CURSOR
FF
or
GG
button to select the
digital input terminal.
Audio Input Setup
Make the audio-related settings.
4
Press the ENTER button to enter the
setting.
• The “Audio Input Setup” menu reappears.
Select from among COAX 1 to 3, OPT 1 to 5.
If the same digital input terminal is selected, the
setting for the input source that was previously
assigned switches to “OFF”.
The HDMI input terminal is displayed when it is
assigned to the input source at “HDMI/DVI In
Assign” ( page 44, 45).
If an input source is assigned to a device
connected with an IEEE1394 cable at “IEEE1394
Assign”, the digital input connector’s assignment
setting switches to “OFF”.
If “Yes” is selected for “Default”, the settings
are automatically reset to the default values.
• The OPTICAL 2, 3 and 4 terminals on the AVC-
A11XV’s rear panel are equipped with an optical
digital output terminal for recording digital audio
signals to a CD recorder, MD recorder, or other
digital audio recording deck. Use this for digital
recording between a digital audio source (stereo – 2
channel) and a digital audio recorder.
• “PHONO” cannot be selected on the “Digital In
Assign” screen.
Setting the DENON LINK
• When a DENON DVD player and the DENON LINK
have been connected, be sure to make a setting to
“DENON LINK” with the System Setup Digital In
Assignment.
• When the input mode is AUTO and the signals are
not be able to transferred by DENON LINK, the unit
automatically changes over the input to the selected
signals (ANALOG, EXT. IN or IEEE1394).
• Refer to “DENON LINK connections” ( page
16).
1
Press the CURSOR
DD
or
HH
button to
select the input source, then press the
CURSOR
FF
or
GG
button to select the
“DLINK”.
2
Press the CURSOR
DD
or
HH
button to
select the “DLINK” setting, then press
the
CURSOR
FF
or
GG
button to select the
input signal (ANALOG, EXT. IN or
IEEE1394).
Select the input for the playback of signals that
cannot be transferred by DENON LINK.
Setting the EXT. IN Setup
• Set the method of playback of the analog input
signal connected to the EXT. IN (8CH) terminal.
• Refer to “Connecting the external inputs (EXT. IN)
terminals” ( page 14).
1
Press the CURSOR
DD
or
HH
button to
select the “EXT. IN Setup” at the
“Audio Input Setup” menu, then press
the
ENTER button.
• Display the “EXT. IN Setup” screen.
2
Press the CURSOR
DD
or
HH
button to
select the item to be set, then press the
CURSOR
FF
or
GG
button to select the
parameter.
SW Level:
Sets the playback level of the analog signal that
was input to the EXT. IN subwoofer terminal.
Select according to the specifications of the player
being used. Also refer to the player’s operating
instructions.
+15dB (default) recommended. (0, +5, +10 and
+15 can be selected.)
Surr. Sp:
Presets the surround speakers that are used in the
EXT. IN mode.
Select according to the specifications of the player
being used. Also refer to the player’s operating
instructions.
• Surr. A:
Select when using surround speakers A.
• Surr. B:
Select when using surround speakers B.
• Surr. A+B:
Select when using both surround speakers A and
B.
3
Press the ENTER button to enter the
setting.
• The “Audio Input Setup” menu reappears.
To Next Page
Loading...
