43
ENGLISH
Advanced Setup – Part 1 Advanced Setup – Part 1
ENGLISH
Setting the Input Function Level
• Correct the playback level of the different input
sources.
• Adjust the playback levels of the devices connected
to the different input sources to the same level to
eliminate the need for adjusting the main volume
each time the input source is switched.
1
Press the CURSOR
DD
or
HH
button to
select the “Input Function Lev.” at the
“Audio Input Setup” menu, then press
the
ENTER button.
• Display the “Input Function Lev.” screen.
2
Press the CURSOR
DD
or
HH
button to
select the input source, then press the
CURSOR
FF
or
GG
button to adjust the
level.
3
Press the ENTER button to enter the
setting.
• The “Audio Input Setup” menu reappears.
1
Press the CURSOR
DD
or
HH
button to
select the “Function Rename” at the
“Audio Input Setup” menu, then press
the
ENTER button.
• Display the “Function Rename” screen.
2
Press the CURSOR
DD
or
HH
button to
select the input source whose name you
want to change, then press the
CURSOR
FF
or
GG
button.
• The screen switches to the character input
screen.
Setting the Function Rename
The names of the input sources displayed on the front
display and on the on screen display can be changed.
The names or brands of the devices connected to the
input sources can be input.
3
Press the CURSOR
FF
or
GG
button to
move the cursor (
22
) to the character,
number, symbol or punctuation mark
you wish to input, and press the
CURSOR
DD
or
HH
button to select that
character.
AB C D E F G H I J K L M N O P Q
R S T U V W X Y Z a b c d e f g h i j
k l m n o p q r s t u v w x y z 0 1 2 3
4 5 6 7 8 9
! ” # % & ’ ( )
*
+ , – . / : ; < = > ? @ [
\ ] (space)
Up to 8 characters can be input.
If you wish to set the input source back to as it
was initially, press the CURSOR
HH
button with the
input source highlighted.
If “Yes” is selected for “Default”, the setting are
automatically reset to the default name.
5
Once all the characters have been input,
press the
ENTER button.
• The “Function Rename” screen reappears.
6
Press the ENTER button to enter the
setting.
• The “Audio Input Setup” menu reappears.
Setting the IEEE1394 Assign
Assign the device connected by IEEE1394 cable to an
input source. The power of the device to be assigned
must be turned on ahead of time.
1
Press the CURSOR
DD
or
HH
button to
select the “IEEE1394 Assign” at the
“Audio Input Setup” menu, then press
the
ENTER button.
• Display the “IEEE1394 Assign” screen.
2
Press the CURSOR
DD
or
HH
button to
select the device, then press the
CURSOR
FF
or
GG
button to select the
input source.
3
Press the ENTER button to enter the
setting.
• The “Audio Input Setup” menu reappears.
The level can be adjusted between –12 dB and
+12 dB in units of 1 dB.
If “Yes” is selected for “Default”, the settings
are automatically reset to the default values.
• After completing this setting, check that the
playback levels for the different sources are the
same.
Example:
When “DVD” is selected and the CURSOR
FF
or
GG
button is pressed
4
Repeat step 3 to input the input source
name.
Use the same procedure to change other input
source names as well.
• When the input source is selected, the display is as
shown below.
Example:
When the name has been changed to “DVD-A1XV”
To Next Page
Loading...
