47
ENGLISH
Advanced Setup – Part 1 Advanced Setup – Part 1
ENGLISH
Setting the 2ch Direct / Stereo
Set this when you want to change the speaker
settings when the surround mode is set to the 2-
channel Direct or Stereo mode.
1
Press the CURSOR
DD
or
HH
button to
select the “Advanced Playback” at the
“System Setup Menu”, then press the
ENTER button.
• Display the “Advanced Playback” menu
screen.
Example:
This screen is displayed in function of the
settings made at “Speaker Configuration”,
“Subwoofer Setup”, “Delay Time” and
“Crossover Frequency”
2
Press the CURSOR
DD
or
HH
button to
select the “2ch Direct / Stereo” at the
“Advanced Playback” menu, then press
the
ENTER button.
• Display the “2ch Direct / Stereo” screen.
Advanced Playback
Makes more detailed audio playback settings.
2 Setting the front B speakers when
the surround mode is set to the 2-
channel Direct or Stereo
When “Front B” is selected at “Power Amp Assign”
and “Custom” is selected at this setting, the “Front
B” setting is displayed.
To play signals from the Front B speaker when in
the 2-channel Direct or Stereo mode, set “Used”.
3
Press the CURSOR
FF
or
GG
button to
select the “Custom”.
4
Press the CURSOR
DD
or
HH
button to
select the setting, then press the
CURSOR
FF
or
GG
button to select the
parameter.
5
Press the ENTER button to enter the
setting.
• The “Advanced Playback” menu reappears.
Setting the Dolby Digital Setup
Sets the down-mixing method when not using a
center speaker or surround speakers.
1
Press the CURSOR
DD
or
HH
button to
select the “Dolby Digital Setup” at the
“Advanced Playback” menu, then press
the
ENTER button.
• Display the “Dolby Digital Setup” screen.
2
Press the CURSOR
FF
or
GG
button to
select the “ON” if you want to use the
Compression, “OFF” if you do not want
to use it.
OFF:
The dynamic range is not compressed.
ON:
The dynamic range is compressed automatically
according to the combination of speakers being
used.
Set “Compression” to “ON” if it seems that
sound is distorted because the input level
exceeds the allowable input for the front
speakers.
When a center speaker or surround speakers are
not connected, the sounds in those channels are
directed to the front speakers.
3
Press the ENTER button to enter the
setting.
• The “Advanced Playback” menu reappears.
1
Press the CURSOR
DD
or
HH
button to
select the “Auto Surround Mode” at the
“Advanced Playback” menu, then press
the
ENTER button.
• Display the “Auto Surround Mode” screen.
2
Press the CURSOR
FF
or
GG
button to
select the “ON” if you want to use the
auto surround mode, “OFF” if you do
not want to use it.
3
Press the ENTER button to enter the
setting.
• The “Advanced Playback” menu reappears.
Setting the Auto Surround Mode
The surround mode used at last for the four types of
input signals shown below is stored in the memory,
and the signal is automatically played with that
surround mode the next time it is input.
Note that the surround mode setting is also stored
separately for the different input sources.
q Analog and PCM 2-channel signals (STEREO)
w 2-channel signals of Dolby Digital, DTS or other
multi-channel format (DOLBY PL
IIx cinema)
e Multi-channel signals of Dolby Digital, DTS or
other multi-channel format (DOLBY/DTS
SURROUND)
r PCM and DSD multi-channel signals other than
Dolby Digital and DTS (MULTI CH IN)
Default settings are indicated in ( ).
During playback in the PURE DIRECT mode, the
surround mode does not change even if the input
signal is changed.
To Next Page
Loading...
