49
ENGLISH
Advanced Setup – Part 1 Advanced Setup – Part 1
ENGLISH
Option Setup
Make other expert settings.
Setting the Channel Setup
With this setting it is possible to change the number of
channels played in the different zones according to the
purpose.
This configures the AVC-A11XV according to whether
or not you have surround “B” speakers connected,
and whether or not you have surround back (SB)
speaker(s) connected.
The number of channels output from the pre-out
connectors exclusively for ZONE2 and 3 can be set to
“Mono” or “Stereo” according to the method of
playback in the various multi-zones.
Adjustments made in this section will have an
effect on the various “
Setting the Power Amplifier
Assignment
” setting options ( page 49, 50).
1
Press the CURSOR
DD
or
HH
button to
select the “Option Setup” at the
“System Setup Menu”, then press the
ENTER button.
• Display the “Option Setup” menu screen.
3
Press the CURSOR
DD
or
HH
button to
select the zone, then press the
CURSOR
FF
or
GG
button to select the channel
setting.
4
Press the ENTER button to enter the
setting.
• The “Option Setup” menu reappears.
2
Press the CURSOR
DD
or
HH
button to
select the “Channel Setup”, then press
the
ENTER button.
• Display the “Channel Setup” screen.
Main Zone:
• Surr. B:
Not Used:
Select if you do not have speakers connected to
Surround “B”.
Used:
Select if you have speakers connected to
Surround “B”.
• S. Back:
2sp:
Select if you have a pair of surround back
speakers connected (SBL & SBR).
1sp:
Select if you have one surround back speaker
connected to SBL.
Not Used:
Select if you do not have surround back
speaker(s).
Setting the Power Amplifier
Assignment
AVC-A11XV’s power amplifiers for seven channels
(except the front channel), can be assigned to any
channels in the MAIN ZONE, ZONE2 or ZONE3 and
output to the speakers. In this way, power amplifiers
not being used in the main zone can be assigned for
multi-zone use, the front speakers can be connected
with a “Bi-Amp”, etc., so you can create the desired
speaker system.
The available power amplifier channels that can be
re-assigned may differ, according to settings
previously made in the “Channel Setup” menu
( page 49).
1
Press the CURSOR
DD
or
HH
button to
select the “Power Amp Assign” at the
“Option Setup” menu, then press the
ENTER button.
• Display the “Power Amp Assign” screen.
2
Press the CURSOR
DD
or
HH
button to
select the power amplifier to be
assigned, then press the
CURSOR
FF
or
GG
button to select which channel to
assigned the amplifier to.
Center:
If no center speaker is connected in the main
room, the center speaker power amplifier channel
can be assigned to either ZONE2 or ZONE3 if set
to “Mono” at “Channel Setup”.
• ZONE2:
The second zone’s mono output is provided by
the center speaker’s power amplifier.
• ZONE3:
The third zone’s mono output is provided by the
center speaker’s power amplifier.
• – – –:
No signals are output from the center speaker’s
power amplifier channel.
Surr. B:
The Surround B amplifier channels can be re-
assigned if they are not being used in the main
room, and the Surround A amplifier channels are
assigned to either the surround channels or to the
front channels.
• Front B:
This mode sets the Surround B amplifier
channels to drive a second set of stereo outputs
that match the front left and right speakers,
providing a Speaker B option for stereo sound in
another location ( page 47).
• – – –:
No signals are output from the surround back
speaker terminals.
Surr. A:
The Surround A power amplifier channels can be
assigned if Surround B is not activated in the main
room (MAIN ZONE).
• Front:
This provides a bi-amp mode for the two main
front speakers, replicating the front left and front
right amplifier channels’ outputs.
• Front B:
The surround A power amplifier channels can be
used to provide a second set of stereo outputs
that match the front left and right speakers,
providing a Speaker B option for stereo sound in
another location ( page 47).
• ZONE2:
This mode assigns the Surround A amplifier
channels to provide ZONE2 speaker-level
outputs from the Surround A speaker jacks, with
the option of monaural or stereo operation
depending on the “Channel Setup” setting.
• ZONE3:
This mode assigns the Surround A amplifier
channels to provide ZONE3 speaker-level
outputs from the Surround A speaker jacks, with
the option of monaural or stereo operation
depending on the “Channel Setup” setting.
• – – –:
No signals are output from the Surround A
speaker terminals.
If “Mono” is selected for ZONE2 or ZONE3,
monaural (single channel) sound is output from
both of the ZONE2 or ZONE3 left and right
channels pre-amp output terminals.
Zone2:
• Stereo:
Select for stereo playback in ZONE2 (two
channels).
• Mono:
Select for monaural playback in ZONE2 (one
channel).
Zone3:
• Stereo:
Select for stereo playback in ZONE3 (two
channels).
• Mono:
Select for monaural playback in ZONE3 (one
channel).
To Next Page
Loading...
