51
ENGLISH
Advanced Setup – Part 1 Advanced Setup – Part 1
ENGLISH
Setting the Trigger Out
• Three 12 V DC Trigger Outputs on the rear panel can
be used to control other devices with compatible
trigger inputs, such as motorized screens, motorized
screen masking, motorized drapes, and other trigger-
controlled devices.
• Set the DC output supplied from the trigger out
terminals for the various input sources to “ON” or
“OFF”.
1
Press the CURSOR
DD
or
HH
button to
select the “Trigger Out” at the “Option
Setup” menu, then press the
ENTER
button.
• Display the “Trigger Out” screen.
2
Press the CURSOR
DD
or
HH
button to
select the trigger out terminal you want
to set, then press the
ENTER button.
• Switch to the setting screen.
3
Press the CURSOR
FF
or
GG
button to
select the zone (MAIN ZONE, ZONE2
and ZONE3).
4
Press the CURSOR
DD
or
HH
button to
select the input source, then press the
CURSOR
FF
or
GG
button to select the
“ON” or “OFF”.
ON:
When that input source is selected, the power
supplied from the trigger out terminal turns on.
OFF:
When that input source is selected, the power
supplied from the trigger out terminal turns off.
If “MAIN” was selected at step 3:
Press the
CURSOR
DD
or
HH
button to
select the surround mode, then press the
CURSOR
FF
or
GG
button to select the
“ON” or “OFF”.
5
ON:
If that surround mode is selected when an input
source set to “ON” is selected, the power
supplied from the trigger out terminal turns on.
OFF:
If that surround mode is selected when an input
source set to “ON” is selected, the power
supplied from the trigger out terminal turns off.
6
Press the ENTER button.
• Return to the “Trigger Out” screen.
Press the CURSOR
DD
or
HH
button to
select the “Exit”, then press the
ENTER
button.
• The “Option Setup” menu reappears.
7
If “Yes” is selected for “Default”, the setting are
automatically reset to the default values.
Example:
When “Trigger Out 1” is selected
The power supplied from the trigger out terminal
turns on and off when the power for the set zone
is turned on and off.
Use the same procedure to make the settings for
Trigger Out 2, 3.
ZONE2 and ZONE3 tone control and
channel level setting
Adjust the sound output from ZONE2 and ZONE3.
1
Press the CURSOR
DD
or
HH
button to
select the “Zone2/3 Tone/Ch Lev.” at the
“Option Setup” menu, then press the
ENTER button.
• Display the “Zone2/3 Tone/Ch Lev.” screen.
2
Press the CURSOR
DD
or
HH
button to
select the zone whose sound you want to
adjust (ZONE2, ZONE3), then press the
ENTER button.
• Switch to the setting screen.
3
Press the CURSOR
DD
or
HH
button to
select the item to be set, then press the
CURSOR
FF
or
GG
button to adjust the
parameter.
Bass:
Adjust the tone for the bass.
Channel Level:
Set so that the playback level is the same for the
left and right channels. (The volume can adjusted
between –12 dB and +12 dB in steps of 1.0 dB.)
Treble:
Adjust the tone for the treble. (The bass or treble
sound can be adjusted between –12 dB and +12
dB in steps of 2.0 dB.)
HPF:
Set this to “ON” if your speakers do not have a
very strong capacity for producing low bass. Using
the high pass filter makes it possible to reduce
distortion of the bass sound.
Press the ENTER button.
• Return to the “Zone2/3 Tone/Ch Lev.”
screen.
4
Use the same procedure to make the settings for
ZONE3.
Example:
When “Zone2” is selected
• The “Channel Level” setting is only possible when
ZONE2 or ZONE3 is set to Stereo in the “Channel
Setup” menu.
Press the CURSOR
DD
or
HH
button to
select the “Exit”, then press the
ENTER
button.
•The “Option Setup” menu reappears.
5
To Next Page
Loading...
