56
ENGLISH
Advanced Setup – Part 2 Advanced Setup – Part 2
ENGLISH
2
Press the CURSOR
FF
or
GG
button to
select the frequency.
FIXED –THX–:
Set to the THX rated 80 Hz crossover frequency.
VARIABLE 40, 60, 80, 90, 100, 110, 120, 150, 200,
250 Hz:
Set as desired according to your speakers’ bass
playback ability.
Advanced:
The crossover frequency can be set individually for
the different speakers ( page 56).
3
Press the ENTER button to enter the
setting.
• The “Speaker Setup” menu reappears.
• Please set all THX Certifies speakers to small and
the crossover to 80Hz.
•We recommend using with the crossover frequency
set to “FIXED–THX–”, but depending on the
speaker, setting it to a different frequency may
improve frequency response near the crossover
frequency.
• The crossover frequency mode is valid only when
subwoofer is set to ON, and when one or more
speakers are set to SMALL, as described in section
“Speaker Configuration” settings ( page 53).
1
Press the CURSOR
FF
or
GG
button to
select the “Advanced” at the “Crossover
Frequency” screen.
2
Press the CURSOR
DD
or
HH
button to
select the speaker to be set.
Setting the crossover frequency
individually for the different channels
• If “LFE+Main” is set at “Subwoofer Setup”,
“SW:LFE+Main” ( page 53, 54) is displayed at
the top right of the screen.
• If “LFE+Main” is set at “Subwoofer Setup”, the
frequencies can be selected regardless of the
speaker size setting.
3
Press the CURSOR
FF
or
GG
button to
select the frequency.
• If “LFE–THX–” is selected at “Subwoofer Setup”,
the frequencies can only be selected for speakers
set to “Small” at “Speaker Configuration”.
Selecting the surround speakers for
the different surround modes
• This menu is displayed when both surround
speakers A and B are used.
• At this screen preset the surround speakers to be
used in each surround modes.
1
Press the CURSOR
DD
or
HH
button to
select the “Surround Sp Setup” at the
“Speaker Setup” menu, then press the
ENTER button.
• Display the “Surround Sp Setup” screen.
2 About Speaker type setting when
using both surround speakers A and
B
If “Small” is set for either surround speakers A or B,
the output is the same as when “Small” is set for both
A and B.
Settings for using a THX Ultra2
compatible subwoofer
Make these settings when “Yes” is selected for the
subwoofer in the “Speaker Configuration” settings.
There is not displayed when “No” selected (
page 53).
1
Press the CURSOR
DD
or
HH
button to
select the “THX Audio Setup” at the
“Speaker Setup” menu, then press the
ENTER button.
• Display the “THX Audio Setup” screen.
2
Press the CURSOR
DD
or
HH
button to
select the surround mode, then press the
CURSOR
FF
or
GG
button to select the
surround speaker.
A:
When surround speakers A is used.
B:
When surround speakers B is used.
A + B:
When both surround speakers A and B are used.
3
Press the ENTER button to enter the
setting.
• The “Speaker Setup” menu reappears.
2
Press the CURSOR
DD
or
HH
button to
select the “Boundary Gain
Compensation”, then press the
ENTER
button.
3
Press the CURSOR
FF
or
GG
button, when
using a THX Ultra2 compatible
subwoofer or subwoofer that frequency
response extends to 20 Hz, select “Yes”.
Otherwise select “No”.
• For the “WIDE SCREEN” and “7CH STEREO” DSP
simulation modes, the surround speakers can be set
separately.
To Next Page
Loading...
