Denon AVC-X8500H - Page 155

Paths to be conrmed Display Settings What to conrm
13 7.1ch g.A13
A19:7.1CH IN
Input Source : CBL/SAT
Input Mode : 7.1ch In
Amp assign : 13.1ch
Floor Layout : 5ch&SB
Height Sp : None
Dolby Sp : None
Speaker Cong ALL Speaker = Small/SW = Yes(2ch)
・ 7.1ch IN input ⇒ Speaker output (Front L/R, Center, Surround L/R, S.Back L/R)
・ 7.1ch IN input ⇒ Pre output (Front L/R, Center, Surround L/R, S.Back L/R, Subwoofer1/2)
14
Amp Assign Cus-
tom (Case1)
g.A14a
g.A14b
A24:CUSTOM1
Input Source : CBL/SAT
Input Mode : Auto
Sound mode : MULTI CH STEREO
Amp assign : Custom
Floor Layout : 5ch&SB
Height Sp : 6ch
Dolby Sp : None
Height Layout : Front Height/Top Middle/Rear Height
Speaker Select=Floor & Height
MAIN ZONE : ON
ZONE2 : OFF
ZONE3 : OFF
Setting
Front Terminal : Rear Height
Surround Terminal : Top Middle
S.Back Terminal : Front Height
Height1 Terminal : S.Back
Height2 Terminal : Front
Height3 Terminal : Surround
・ Analog 入力 ⇒ Speaker 出力
(Front L/R (Rear Height), Surround L/R (Top Middle), S.Back L/R (Front Height), Height1 L/R
(S.Back), Height2 L/R (Front), Height3 L/R (Surround))
(
b
The input source can be switched to any source except CBL/SAT.)
(
b
Volume 60 is the value when Absolute settings are used. The value is -20 when Relative set-
tings are used)
15
Amp Assign Cus-
tom (Case2)
g.A15a
g.A15b
A25:CUSTOM2
Input Source : CBL/SAT
Input Mode : Auto
Sound mode : MULTI CH STEREO
Amp assign : Custom
Floor Layout : 5ch&SB
Height Sp : 6ch
Dolby Sp : None
Height Layout : Front Height/Top Middle/Rear Height
Speaker Select=Floor & Height
MAIN ZONE : ON
ZONE2 : OFF
ZONE3 : OFF
Setting
Front Terminal : Center
Surround Terminal : Surround
S.Back Terminal : Center
Height1 Terminal : Front Height
Height2 Terminal : Rear Height
Height3 Terminal : Top Middle
・ Analog input ⇒ Speaker output
(Front L/R (Center), S.Back L/R (Center))
(
b
The input source can be switched to any source except CBL/SAT.)
(
b
Volume 60 is the value when Absolute settings are used. The value is -20 when Relative set-
tings are used)
16
Amp Assign Cus-
tom (Case3)
g.A16a
g.A16b
A26:CUSTOM3
Input Source : CBL/SAT
Input Mode : Auto
Sound mode : MULTI CH STEREO
Amp assign : Custom
Floor Layout : 5ch&SB
Height Sp : 6ch
Dolby Sp : None
Height Layout : Front Height/Top Middle/Rear Height
Speaker Select=Floor & Height
MAIN ZONE : ON
ZONE2 : ON
ZONE3 : ON
Setting
Front Terminal : ZONE2
Surround Terminal : ZONE3
S.Back Terminal : L : ZONE2 (U3219 10pin)
R : ZONE3 (U3219 11pin)
Height1 Terminal : L : ZONE2 (U3220 10pin)
R : ZONE3 (U3220 11pin)
Height2 Terminal : ZONE2
Height3 Terminal : ZONE3
・ Analog 入力 ⇒ Speaker 出力
(Front L/R (Zone2), Surround L/R (Zone3), S.Back L/R (L:Zone2L / R:Zone3R), Height1 L/R
(L:Zone2L / R:Zone3R), Height2 L/R (Zone2), Height3 L/R (Zone3))
(
b
The input source can be switched to any source except CBL/SAT.)
(
b
Volume 60 is the value when Absolute settings are used. The value is -20 when Relative set-
tings are used)
Before Servicing
This Unit
Electrical Mechanical Repair Information Updating
155