38
AVR-3801
Resistors
Ex.: RN 14K 2E 182 G FR
Type Shape Power Resist- Allowable Others
and per- ance error
formance
Resistance
1 8 2 ⇒ 1800 ohm = 1.8 kohm
Indicates number of zeros after effective number.
2-digit effective number.
•
Units: ohm
1 R 2 ⇒ 1.2 ohm
1-digit effective number.
2-digit effective number, decimal point indicated by R.
•
Units: ohm
Capacitors
Ex.: CE 04W 1H 2R2 M BP
Type Shape Dielectric Capacity Allowable Others
and per- strength error
formance
Capacity (electrolyte only)
2 2 2 ⇒ 2200µF
Indicates number of zeros after effective number.
2-digit effective number.
•
Units: µF.
2 R 2 ⇒ 2.2µF
1-digit effective number.
2-digit effective number, decimal point indicated by R.
•
Units: µF.
Capacity (except electrolyte)
2 2 2 ⇒ 2200pF=0.0022µF
(More than 2) Indicates number of zeros after effective number.
2-digit effective number.
•
Units: µF.
2 2 1 ⇒ 220pF
(0 or 1) Indicates number of zeros after effective number.
2-digit effective number.
•
Units: pF.
•
When the dielectric strength is indicated in AC, "AC" is included after the dieelectric
strength value.
NOTE FOR PARTS LIST
l Part indicated with the mark "" are not always in stock and possibly to take a long period of time for supplying, or in
some case supplying of part may be refused.
l When ordering of part, clearly indicate "1" and "I" (i) to avoid mis-supplying.
l Ordering part without stating its part number can not be supplied.
l Part indicated with the mark "" is not illustrated in the exploded view.
l Not including Carbon Film ±5%, 1/4W Type in the P.W.Board parts list. (Refer to the Schematic Diagram for those parts.)
WARNING:
Parts marked with this symbol
have critical characteristics.
Use ONLY replacement parts recommended by the manufacturer.
CE : Aluminum foil 0J : 6.3V F :
±
1% HS : High stability type
electrolytic
CA : Aluminum solid 1A : 10V G :
±
2% BP : Non-polar type
electrolytic
CS : Tantalum electrolytic 1C : 16V J :
±
5% HR : Ripple-resistant type
CQ : Film 1E : 25V K :
±
10% DL : For change and discharge
CK : Ceramic 1V : 35V M :
±
20% HF : For assuring high
frequency
CC : Ceramic 1H : 50V Z : +80% U : UL part
CP : Oil 2A : 100V 20% C : CSA part
CM : Mica 2B : 125V P : +100% W : UL-CSA type
CF : Metallized 2C : 160V 0% F : Lead wire forming
CH : Metallized 2D : 200V C :
±
0.25pF
2E : 250V D :
±
0.5pF
2H : 500V = : Others
2J : 630V
RD : Carbon 2B : 1/8W F : ±1% P : Pulse-resistant type
RC : Composition 2E : 1/4W G :
±
2% NL : Low noise type
RS : Metal oxide film 2H : 1/2W J :
±
5% NB : Non-burning type
RW : Winding 3A : 1W K :
±
10% FR : Fuse-resistor
RN : Metal film 3D : 2W M :
±
20% F : Lead wire forming
RK : Metal mixture 3F : 3W
3H : 5W
To Next Page
Loading...
