Denon AVR-5805 - Fader Function

161
Fader function
• This function makes it possible to lower the volume of the front channels (FL, C and FR) or the rear channels (SL, SR, SBL and SBR) of Zone2
together. Use it for example to adjust the balance of the sound from each position when multi-channel music sources are played.
2
The Channel Volume screen is displayed at Zone2
monitor out.
4
Press the Cursor left button to reduce the volume of the front channels, the Cursor right button to reduce the
volume of the rear channels.
The fader function does not affect the SW channel.
• The channel whose channel level is adjusted lowest can be faded to –12 dB using the fader function.
• If the channel levels are adjusted separately after adjusting the fader, the fader adjustment values are cleared, so
adjust the fader again.
RC-995
1
3,4
2,3
1
Select the ZONE2 mode using the AMP/Z2 button.
CH SEL
ENTER
(Remote control unit)
¥¥¥¥¥¥ńţŜũũŠŧ¥ŗŪŧ©
¥
Ňō¥¥¥¥¥ĸ©ĸ
şŃ¥ Ŕœ¥¥¥¥¥ĸ©ĸ şŃ
ń¥¥¥¥¥¥ĸ©ĸ şŃ¥ ŔŃœ¥¥¥¥ĸ©ĸ şŃ
Ňœ¥¥¥¥¥ĸ©ĸ şŃ¥ ŔŃō¥¥¥¥ĸ©ĸ şŃ
ŔŘ¥¥¥¥¥ĸ©ĸ şŃ¥ Ŕō¥¥¥¥¥ĸ©ĸ şŃ
¥
¥
¥¥¥¥¥¥¥¥¥¥¥¥ŇŜşŠŭ
¥¥¥¥¥¥¥¥¥¥¥¥ŇœŐŏŕ¥«¥œņłœ
Select “FADER”.
• When pressing the ENTER button, the channel
switches in oder shown below each time the
ENTER button is pressed.
CH SEL
ENTER
(Remote control unit)
(Remote control unit)
CH SEL
ENTER
CH SEL
ENTER
or
(Remote control unit)
3
FADER
SR
SBR
SBL
SL
FL
C
FR
SW
¥¥¥¥¥¥ńţŜũũŠŧ¥ŗŪŧ©
¥
Ňō¥¥¥¥¥ĸ©ĸ
şŃ¥ Ŕœ¥¥¥¥¥ĸ©ĸ şŃ
ń¥¥¥¥¥¥ĸ©ĸ şŃ¥ ŔŃœ¥¥¥¥ĸ©ĸ şŃ
Ňœ¥¥¥¥¥ĸ©ĸ şŃ¥ ŔŃō¥¥¥¥ĸ©ĸ şŃ
ŔŘ¥¥¥¥¥ĸ©ĸ şŃ¥ Ŕō¥¥¥¥¥ĸ©ĸ şŃ
¥
¥
¥¥¥¥¥¥¥¥¥¥¥¥ŇŜşŠŭ
¥¥¥¥¥¥¥¥¥¥¥¥ŇœŐŏŕ¥«¥œņłœ
Zone2 surround back speakers are only displayed when “7.1ch” is selected for the Zone2 channel output setting
at “7-1. Channel Setup”.
When the Zone2 surround back speaker setting is set to “1spkr” for “6-1. Speaker Configuration”, this is set to
“SB”.