Denon AVR-X2100W Service Manual

Error
Code
Details of Error code Display Coping strategies
86
Mismatched CheckSum in Check-
Sum comparison after rewriting.
U p d a t i n g f a i l 8 6
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error dis-
play, press and hold the "Power opera-
tion" button for ve seconds.
A2
Unable to detect USB.
C o n n e c t i o n F a i l A 2
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error dis-
play, press and hold the "Power opera-
tion" button for ve seconds.
A3
No FirmwareFile in USB.
F i l e s N o t F o u n d A 3
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error dis-
play, press and hold the "Power opera-
tion" button for ve seconds.
A4
FirmwareFile in USB for unsup-
ported Model name/area.
N o t M a t c h F i r m A 4
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error dis-
play, press and hold the "Power opera-
tion" button for ve seconds.
A6
Error notication received while
requesting FirmwareInfo.
U p d a t i n g f a i l A 6
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error dis-
play, press and hold the "Power opera-
tion" button for ve seconds.
A7
TimeOut while obtaining Firmware
information.
U p d a t i n g f a i l A 7
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error dis-
play, press and hold the "Power opera-
tion" button for ve seconds.
AE
Unable to detect USB for Firm-
wareDownload.
C o n n e c t i o n F a i l A E
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error dis-
play, press and hold the "Power opera-
tion" button for ve seconds.
AF
No FirmwareFile for Firmware-
Download.
F i l e s N o t F o u n d A F
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error dis-
play, press and hold the "Power opera-
tion" button for ve seconds.
B1
TimeOut in Download (writing to
SDRAM) for FirmwareDownload.
D o w n l o a d f a i l B 1
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error dis-
play, press and hold the "Power opera-
tion" button for ve seconds.
B2
Error notication received after
rewriting CX870 Firm.
U p d a t i n g f a i l B 2
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error dis-
play, press and hold the "Power opera-
tion" button for ve seconds.
B3
Error in FirmwareUpdate (Time-
Out).
U p d a t i n g f a i l B 3
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error dis-
play, press and hold the "Power opera-
tion" button for ve seconds.
B4
Failed to transit to BootLoader-
Mode.
U p d a t i n g f a i l B 4
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error dis-
play, press and hold the "Power opera-
tion" button for ve seconds.
B5
Failed to transit to Application-
Mode.
U p d a t i n g f a i l B 5
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error dis-
play, press and hold the "Power opera-
tion" button for ve seconds.
---Check the rmware version after updating.---
After updating the rmware, check the version. See "
1. Version Display Mode
" (21 page ).
67

Denon AVR-X2100W Specifications

General

Receiver type	Surround
Frequency range	10 - 100000 Hz
Audio output channels	7.1 channels
Signal-to-Noise Ratio (SNR)	100 dB
Power output per channel (1KHz@6 Ohm)	150 W
Power output per channel (20-20KHz@8 Ohm)	95 W
HDMI in	8
Composite video in	2
Component video (YPbPr/YCbCr) in	1
Speakers connectivity type	-
Ethernet LAN	Yes
AM band range	522 - 1611 kHz
FM band range	87.5 - 108 MHz
Supported radio bands	AM, FM
Optical drive included	No
Product color	Black
Audio decoders	Dolby Digital EX, Dolby Pro Logic IIx, Dolby TrueHD, DTS 96/24, DTS-ES, DTS-HD
Apple docking compatibility	iPhone, iPod
AC input voltage	230 V
AC input frequency	50 Hz
Power consumption (standby)	0.1 W
Power consumption (typical)	500 W

Weight and Dimensions

Depth	339 mm
Width	434 mm
Height	167 mm
Weight	9700 g