Denon AVR-X4400H User Manual

.
Multi Ch Stereo
SDDDz10 Dz10 Dz10 Dz10 Dz10 Dz10 Dz10 Dz10 Dz10 Dz10 Dz10 D
Rock Arena
SDDDz10 Dz10 Dz10 Dz10 Dz10 Dz10 Dz10 Dz10 Dz10 Dz10 Dz10 D
Jazz Club
SDDDz10 Dz10 Dz10 Dz10 Dz10 Dz10 Dz10 Dz10 Dz10 Dz10 Dz10 D
Mono Movie
SDDDz10 Dz10 Dz10 Dz10 Dz10 Dz10 Dz10 Dz10 Dz10 Dz10 Dz10 D
Video Game
SDDDz10 Dz10 Dz10 Dz10 Dz10 Dz10 Dz10 Dz10 Dz10 Dz10 Dz10 D
Matrix
SDDDz10 Dz10 Dz10 Dz10 Dz10 Dz10 Dz10 Dz10 Dz10 Dz10 Dz10 D
Virtual
S D
Sound mode
Front
L/R
Center
Surround
L/R
Surround
Back
L/R
Front
Height
L/R
Top Front
L/R
Top
Middle
L/R
Channel output
Top Rear
L/R
Rear
Height
L/R
Surround
Height
L/R
Top
Surround
Front Dolby
Atmos
Enabled
L/R
Surround
Dolby
Atmos
Enabled
L/R
Back Dolby
Atmos
Enabled
L/R
Subwoofer
z1
The applicable sound mode includes “Dolby Surround” and sound modes that have “+Dolby Surround” in the sound mode name.
z2
The applicable sound mode includes “DTS Neural:X” and sound modes that have “+Neural:X” in the sound mode name.
z3
The applicable sound mode includes “DTS Virtual:X” and sound modes that have “+Virtual:X” in the sound mode name.
z4
A signal for each channel contained in an input signal is output as audio.
z5 Audio is output when “Subwoofer Mode” in the menu is set to “LFE+Main”. (v
p. 232)
z6 Audio is not output when “Speaker Config.” - “Surr. Back” in the menu is set to “1 spkr”. (v p. 225)
z7
For the best Auro-3D experience Surround Height speakers are recommended, however you may substitute Rear Height speakers from a Dolby Atmos speaker setup in
place of Surround Height speakers.
z8
This is output if an Auro-3D signal is input and the input signal contains Top Surround.
z9
For the best Auro-3D experience Front Height and Surround Height speakers are recommended, however you may substitute Dolby Atmos Enabled speakers.
z10 Audio is output from the speakers specified in the “Surround Parameter” – “Speaker Select” settings. (v
p. 177)
Contents
Connections Playback Settings Tips Appendix
299
Front panel Display Rear panel Remote Index

Denon AVR-X4400H Specifications

General

Display	-
ECO mode	Yes
HDCP version	2.2
Apple docking	No
Product color	Black
Audio decoders	DTS:X, Dolby Atmos
Audio formats supported	ALAC, DSD, FLAC, WAV
AM band range	522 - 1611 kHz
FM band range	87.5 - 108 MHz
Supported radio bands	AM, FM
Supported graphics resolutions	4096 x 2160
RS-232 ports	1
Connectivity technology	Wireless
HDMI in	8
Composite video in	4
Component video (YPbPr/YCbCr) in	2
Receiver type	Surround
Frequency range	10 - 100000 Hz
Pre-out channels	11.2
Input sensitivity	200 mV
Audio output channels	9.2 channels
Signal-to-Noise Ratio (SNR)	100 dB
Power output per channel (1KHz@6 Ohm)	200 W
Power output per channel (20-20KHz@8 Ohm)	125 W
AC input voltage	230 V
AC input frequency	50 Hz
Power consumption (standby)	0.5 W
Power consumption (typical)	710 W
Number of HDMI outputs	3

Weight and Dimensions

Depth	389 mm
Width	434 mm
Height	167 mm
Weight	13500 g