Denon DN-2600F - Sampler, Digital Scratch, and Effector Functions (Part 4); Effector Functions: Filter, Reverb, and Flanger Details

ENGLISH
20
2-2
3
4
Select the high frequency range to be filtered.
Turn the data master knob (8—9).
• If the data master knob (8—9) is pressed again, the
player returns to the same status as in step 1-2.
• The frequency can be set between 100 Hz and 20 kHz (or
none).
✽ The high frequency cannot be set below than the low
frequency.
NOTE:
• For some tracks, clipping may occur in the playback
sound.
Start filtered playback.
Press the ON/OFF button at any point between steps 1-1
and 2-2.
Canceling the filter frequency input mode.
Press the FIL/REVERSE button.
• The “ ” indicator is lit when the filter is on.
• The “ ” indicator is not lit when the filter is off.
• When pressed again, the filter turns off.
FIL ON FIL OFF
Using the reverb function
★ With this function, an echo is produced at the set tempo.
1-1
1-2
2-1
2-2
Set the reverb delay time input mode.
Press the RVB/LOOP button.
Select the reverb delay time.
Turn the data master knob (
8—9).
Set the reverb feedback number mode.
Press the data master knob (8—9).
Select the reverb feedback number.
Turn the data master knob (8—9).
• If the data master knob (
8—9) is pressed again, the
player returns to the same status as in step 1-2.
• The time can be set to 2/1, 1/1, 3/4, 1/2, 1/4 or 1/8 the
BPM set with the TAP (TAP/BPM) button.
***bpm 1/2
***bpm 1/2
EFFECT
Flashing
L F.Back H

Feedback number
PUSH ENTER
The feedback number increases when the
knob is turned clockwise and decreases
when the knob is turned counterclockwise.
3
4
Start reverb playback.
Press the ON/OFF button at any point between steps 1-1
and 2-2.
Canceling the reverb data setting mode.
Press the RVB/LOOP button.
• The “ ” indicator is lit when the reverb mode is on.
• The “ ” indicator is not lit when the reverb mode is
off.
• When pressed again, reverb playback stops.
RVB ON RVB OFF
Using the flanger function
★ With this function you can create swelling sounds.
1-1
1-2
2-1
2-2
3
4
Set the flanger time input mode.
Press the FLG/PITCH button.
Select the flanger time.
Turn the data master knob (
8—9).
• The time can be set to 4/1, 2/1, 1/1, 3/4, 1/2, 1/4 or 1/8
the BPM set with the TAP (TAP/BPM) button.
Set the flanger gain input mode.
Press the data master knob (8—9).
Select the flanger gain.
Turn the data master knob (
8—9).
Start flanger playback.
Press the ON/OFF button.
Canceling the flanger data setting mode.
Press the FLG/PITCH button.
• The “ ” indicator is lit when the flanger mode is on.
• The “ ” indicator is not lit when the flanger mode is
off.
• When pressed again, flanger playback stops.
***bpm 1/4
EFFECT
Flashing
L Gain H
Gain
• If the data master knob (8—9) is pressed again, the
player returns to the same status as in step 1-2.
PUSH ENTER
The gain increases when the knob is turned
clockwise and decreases when the knob is
turned counterclockwise.
FLG ON FLG OFF
NOTE:
• For some tracks, clipping may occur in the playback sound.