Denon DRA-565RD - Panel Control Designations and Functions; Front Panel Controls and Indicators; Rear Panel Terminals

DESIGNATIONS AND FUNCTIONS OF PANEL CONTROLS (Refer to Page 5.)
FRONT PANEL
0
POWER (Power ON-STANOBY/OFF Switch)
This switch turns the unit ON or OFF. There is a delay of
approximatety 3 seconds before the unit will operste after
this power switch is turned ON. If the unit is turned OFF
from the remote control, the unit will be in the STANDBY
mode. When in the STANOBY mode, the unit can be turned
ON with the power button on the remote control. If the unit
will not be used for extended period, be sure to turn the
unit OFF from the front panel power switch.
NOTE: This unk includes ea STANOBY protection feature.
This feature is designed to prevent accidental
turn-on from the STANDBY mode in the event of
® power failure. Should AC power be discon-
nected and then reconnected when the unit is in
STANDBY mode, the unit will return to the
STANDBY mode.
To turn the unit ON from the STANOBY mode
without the remote control, operate the front
panel power switch four times. The unit will then
operate normally.
PHONES (Heedphones jack)
Connect a pair of headphones (sold separately) to this jack
for private listening.
SPEAKERS (Speaker selector switches)
These switches sre used fo select spesker system A and B.
No sound Is heard through the speakers when both
switches are reset to the ( m ) position.
REMOTE SENSOR (Remote contro! sensor)
This sensor receives the infra-red light transmitted from the
wireless remote control unit.
For remote control, point the wireless remote control unit
towards the sensor,
BASS (Bass control)
Use this contro! to adjust the low-range response.
When the control is set to the center position, the frequency
characteristic curve (below 1.000 Hz) is fiat. Turn the control
clockwise to increase the bass response and counter-
Clockwise to decrease it.
TREBLE (Treble control)
Use this control to adjust the high-range response.
When the control is set to the center position, the frequency
characteristic curve [above 1,000 Hz} is fiat. Tuen the contro!
clockwise to increase the trable response and counter:
clockwise to decrease it.
BALANCE (Balance contro!)
Use this controt to balance the volume levels between left
and right chenneis. The volume levels in both channels are
equal when the control is set to the center position.
VARIABLE LOUONESS (Loudness control}
At low volumes, the human ear is less sensitive to low
(BASS) and high (TREBLE) frequencies. Use this control to
compensate for this deficiency when listening at low
volume levels. Turn this contro! counter-clockwise until a
natural belance of bess and treble sound hes: been
restored. , :
BASS EQ (DRA-565R0 only)
Press this button to switch the BASS EO ON (=) for
emphasis of bess sounds.
Use in conjunction with the bass adjustment of the tone
control will provide further emphasis of bass sounds. Set
this switch to OFF ( m ) when you wish to listen with a
normal setting condition.
VOLUME (Volume control)
This knob is used to adjust the volume level of both
channets.
Turn the knob clockwise to raise the volume and counter-
clockwise to lower it.
oO
input selector (Input selector buttons)
These buttons are used to select the sudio input source.
oe PHONO: Press to play a record on a record player
connected to the PHONO input jacks.
e CO: Press to listen to a compact disc player or
another component connected to the CO Input
jacks.
e TUNER: Press to fisten to FM ar AM programs.
e VIDEO: Use when playing back the audio from a Hi-Fi
video, video disc player or other component
connected to the VIDEO terminal.
@ Tape selector (Tape selector/monitor buttons)
(DRA-S65RD)
TAPE:1; Press this bution once, TAPE-1 indicator will
light up and then you can pisy tepe source on TAPE-1
terminal.
in this state you can copy TAPE-1 source to TAPE-2
terminal.
TAPE-2: Press this button once, TAPE-2 indicator will
light up and then you can play tape or video source of
TAPE-2 terminal.
Press again the button currently accessed, to play
sources selected by input selector é. indicator goes out.
@ TAPE (Tepe monitor button) (ORA-365RD)
Press this button once, TAPE Indicator will light up and
then you can play tape source on the TAPE terminal.
Press again the button currently accessed, to play
sources selected by input selector @, indicator goes out.
ROS button
This button is used for the ROS search (refer to page 12)
and PTY search (refer to page 12), and TP search (refer to
pege 12) operations, and to input the station name (refer to
pege 12, 13).
BAND (Band selector switch)
Press this switch to select the FM of AM (MY) band.
AUTO (Tuning mode button}
This switches between auto and manual tuning.
Auto tuning: When the UP button is pressed, the radio is
tuned automatically to 8 higher frequency. Press the
DOWN button to tune to @ lower frequency. Use this
postion to eliminate noise when no signals of weak signals
eee being received. «
Manual tuning: In this position, the radio can be tuned
manualty. Reception is eutomaticaity monaural when in the
manual mode.
TUNING (Tuning buttons)
Use these to chenge the received frequency to a higher
frequency (UPi of a lower frequency (DOWN).
When writing station names. use these buttons to select
the letters. (Refer to Page 13.)
MEMORY (Memory button)
This ewitch is used to store the desired radio station to »
memory.
© Presetting stations
After pressing the MEMORY button, press the SHIFY/
PTY button to select the memory block, A to E. Now use
the PRESET UP and DOWN buttons to specify the preset
channel number. Press the MEMORY button agsin to
store the station at the specified preset channel.
Prasat (Preset station buttons)
These duttons are used for storing stations or recalling
stations which have been preset. Using the SHIFT button
you can preset a total of 40 FM of AM stations into preset
channels.
Once 8 radio has been memorized, the seme station can
later be tuned in instantly simply by recalling the corres-
ponding preset channel with PRESET UP or DOWN button.
DISPLAY
8 86 8 88s 6
ROS Indicator
This lights when recaiving ROS broadcasts, and Hashes
during the ROS saarch operations.
TA Indicator
This fights when receiving traffic announcements.
TP indtcator
This fleshes during the TP search operation and fights
when TP stations are tuned in.
PTY indicator
This flashes during the PTY (Programme type) search
operation.
TUNED indicator
This tights when a station is properly tuned in.
STEREO indicator
This lights when receiving stereo broadcasts. It remains off
when receiving AM broadcasts.
AUTO indicator
This indicates the tuning mode. It lights in the auto mode,
and remains off in the manual mode.
NOTE:
© TP (Traffic Programme)
Stations scheduled to brosdcast traffic programmes
e TA (Traffic Announcement)
Traffic information broadcasts
REAR PANEL
(2)
FM ANT (FM antenna terminals)
75-ohm coaxial cable can be connected to this terminal. For
antenna connecting procedure, see the ANTENNA IN-
STALLATION.
GND (Grounding terminal)
The grounding wire of the turntable is connected here.
« Hum or noise may be generated H the grounding wire is
Not connected.
AM ANT (AM antenna terminals}
Connect the attached AM loop antenna. (Refer to page 10
for connections).
Connect to this terminal when e@ medium wave outdoor
antenna is used.
PHONO (Phono Input terminats)
The output cord of the turntable ts connected here.
Since the input sensitivity of “PHONO” is extremety high,
do not use the unk without the input pin cord. If used
without this cord, the speakers mey generate hum.
co
The output cord of the CO player is connected here.
VIDEO
A VIDEO, such as a VCR or Video Dise may be connected
here.
© TAPE-1, TAPE-2 (Tape deck playback / recording
terminal} (DRA-565RD)
Two tape decks of tape deck can be connected to these
jacks for full-fledged playback. recording and tape
dubbing operation.
@ TAPE (ORA-36SRD)
Tape decks can be connected for full use including
playing or copying.
®
Se @
e SHIFT/PTY button
Use this button to select the memory blocks, A (110 8), B
(1 to 8, C (1 to 8), O (1 to 8) or E (1 to 8).
For PTY search. use this bution to select'the program
type.
When writing station names, use this bution to set the
writing position.
MEMO indicator
This indicator lights for approximately 10 seconds when
the MEMORY button has been pressed and 8 station can be
stored on a PRESET CHANNEL button.
This flashes continuously during the auto memory opera.
tion.
CH indicator
This lights when the preset channel number and shih mode
(A, 8, C, 0 of E) are displayed.
© TAPE-1/TAPE-2 indicator (DRA-565R0)
The TAPE-! indicator lights when the TAPE-1 source is
selected with the tape selector buttons. The TAPE.2
indicator lights when the TAPE-2 source is selected.
e@ TAPE Indicator (DRA-365RD)
The TAPE indicator lights when the TAPE source is
selected with the tape selector buttons.
Muti function display
This displays the frequency, station name, programme
type, etc.
PRE-OUT (DRA-565RD only)
Output signais for power amplifiers are sent trom these
jacks.
The rated output is 2 volts.
SPEAKER SYSTEMS (Speaker terminals)
Two pairs of speakers A and B can be connected to these
terminals.
AC OUTLET (AC power outlets)
This AC outlet is controlled by the power switch and
Remoto controtunit (DRA-S65AD), controlied by the power
switch [ORA-365R0).
AC CORO (Power cord)
Connect this cord into the wall outtet.
BQOHSSe/aHsss-vywa AE aA RI I Ie EN Ta SUS SE ED a re ra ee EEO