Denon UDRA-90 - Edited Recording to Cassette Tape; Automatic and Programmed Editing

Editing is possible with CDs containing up to 30 tracks.
Before starting the edited recording operation, ioad the
cassette tape to which you will record into deck with side A
facing up.
The leader tape is automatically taken up before recording
starts.
(Set the REV MODE switch to the =) position.)
DAutomatic Edited Recording .........cccscssssecssseecsseseseeesesesenneecrsneersneeeneses RECORDING IN THE SAME ORDER AS ON THE DISC |
Example: Recording a disc with 18 tracks and a total playing time of 56 minutes onto a C-60 cassette tape
URN CLOSE
aad tee a
yoy
Press the OPEN/CLOSE button. — Set the disc. -- Press the OPEN/CLOSE button. -+
Press the play button and set the function to CD. -+ Press the stop button.
NOTE:
@ With edited recording, side B of the tape will be recorded automatically even when the REV MODE switch of the deck is
set to the >" position.
¢ During edited recording, only the following buttons will function: the stop button of the CD or the OPEN/CLOSE button,
and the stop button of the deck.
@ When using a recorded tape for edited recording, the tape should be erased before use, since when the tape is longer
than the set time, an unrecorded section of side B will remain after the tape stops.
When a tape which has been recorded with this system is played back, there will be 4-second blank portions between
tracks (for making it easy to reach the beginning of a track). This will differ from the actual silent portions between the
tracks on the disc, and so there will be some error in the actual remaining time of the tape and the displayed time.
Press
the
EDIT
button
to
set
the
tape
length.
Setting
the
desired
recording
time
(Method
Press
the
EDIT
button
four
times
when
using
2)
;
a
60-minute
(C
60)
tape.
Select
a
tape
length
close
to
the
desired
(The
tape
length
is
to
total
time
of
sides
A
and
B.)
time,
then
make
a
fine
adjustment
using
the
The
display
changes
as
follows
each
time
the
EDIT
button
is
pressed.
|
14444
or
>>
PPI
button.
{When
the
tape
time
has
already
been
set,
the
display
will
change
in
For
example,
to
set
51
minutes,
select
C-50,
order
starting
at
that
time
each
time
the
EDIT
button
is
pressed.)
then
press
the
PP
PPI
button
once
to
set
= C-51.
46-minute 50-minute 54-minute 60-minute
tape tape tape T2388
67aa%
W112 13 4818
wie
120-minute 100-minute 90-minute 74-minute ide
tape tape tape tape
The desired recording time can be set
when this is displayed.
|
“EDIT” flashes for 2 seconds
2 minutes 40 seconds
extra on side A
Example: For a 36-minute tape, use the I€4 44 or DD DPI
button to set 36.
To set the tape length using the remote control unit, use the
number buttons. For example, in the case of a 30-minute
tape, press twice and press fd] .
|
If you make a mistake, press the
EDIT button to display “C-09", then
start over again.
A oeoy'
PROGRAM EOT od
Tracks for side A light up. Tracks for side B flash.
(Tracks 1 through 9 are recorded on side A.)
(Tracks 10 through 18 are recorded on side 8.)
KS ©
The display changes between sides A and B each time the TAPE
A/B button is pressed.
(Use this to check the
extra time on side B.)
1 minute 20 seconds
extra on side B.
Tracks for side A flash.
Tracks for side B light up.
OPEN /CLOSE
Press the play button.
i ee
@ Note that in some cases, even if the tape is longer than the total playing time on the disc, it may not be possible to record all
the tracks onto the tape, since they are divided onto sides A and B. In such cases, the OVER indicator flashes.
@Programmed Edited Recording .............secssesersesseenesnsenesseesseseesnees RECORDING CERTAIN TRACKS IN ANY DESIRED ORDER
@ Follow the instructions under “PROGRAMMED SELECTION” on Page 20 to program the tracks.
@ Perform steps 2 through 4 under the aforementioned “Automatic Edited Recording”.
Programmed CD Play Using the Search Buttons (I€q €q_ >> PP!)
Pressing the PROGRAM button of the remote control unit will light up the “PROGRAM” indicator. When the disc is
stopped, programming can be done with the search buttons (144 44 >> PPI) on the CD player or with the search buttons
(144 44 DD PPE) on the remote control unit.
e Seiect the tracks with the search buttons, then press the PROGRAM button to program them.
e The search buttons (44 PP) can be used to change the track numbers continuously.
e After the track numbers have been selected with the search buttons, if the play button is pressed to start CD play before
the PROGRAM button is pressed, the last track of the program set up to this point wili be played.
In this case, the tracks selected with the search buttons will not be programmed.
21