DeWalt DCF403 - Power Tool Use and Care; General Tool Use and Care; Battery Tool Use and Care; Tool Servicing and Maintenance

5
ENGLISH
of battery pack may create a risk of fire when used with
another batterypack.
b ) Use power tools only with specifically designated
battery packs. Use of any other battery packs may create
a risk of injury andfire.
c ) When battery pack is not in use, keep it away from
other metal objects, like paper clips, coins, keys,
nails, screws or other small metal objects, that can
make a connection from one terminal to another.
Shorting the battery terminals together may cause burns
or afire.
d ) Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact
accidentally occurs, flush with water. If liquid
contacts eyes, additionally seek medical help. Liquid
ejected from the battery may cause irritation orburns.
e ) Do not use a battery pack or tool that is damaged or
modified. Damaged or modified batteries may exhibit
unpredictable behaviour resulting in fire, explosion or risk
ofinjury.
f ) Do not expose a battery pack or tool to fire or
excessive temperature. Exposure to fire or temperature
above 130°C may causeexplosion.
g ) Follow all charging instructions and do not charge
the battery pack or tool outside the temperature
range specified in the instructions. Charging
improperly or at temperatures outside the specified range
may damage the battery and increase the risk offire.
6) Service
a ) Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool ismaintained.
b ) Never service damaged battery packs. Service
of battery packs should only be performed by the
manufacturer or authorised serviceproviders.
Riveter Safety Warnings

WARNING: Never modify the power tool or any part of it.
Damage or personal injury couldresult.

WARNING: ALWAYS use safety glasses. Everyday
eyeglasses are NOT safety glasses. ALWAYS WEAR
CERTIFIED SAFETYEQUIPMENT:
• Do not work without a collection container. Mandrels are
ejected to the rear by the riveter and can causeinjuries.
• Do not point the riveter at persons or yourself during
operation and do not work without material to be
riveted. The blind rivet can be ejected from the riveter and
causeinjuries.
• After the riveting process is completed tilt the unit
backwards, so that the residual mandrels fall into the
collectioncontainer.
• Ventilation slots for the engine must not be covered;
do not insert any objects into them. Damage or personal
injury couldresult.
• When not in use, place tool on its side on a stable surface
where it will not cause a tripping or falling hazard. Some
tools with large battery packs will stand upright on the battery
pack but may be easily knockedover.
• Disconnect the power tool from the power supply/
battery if it cannot be switched off. Do not use the power
tool if it cannot be switched on and off with the switch.
Any power tool that cannot be controlled with the switch is
dangerous and must berepaired.
Residual Risks
In spite of the application of the relevant safety regulations
and the implementation of safety devices, certain residual risks
cannot be avoided. These are:
• Impairment ofhearing.
• Risk of personal injury due to flyingparticles.
• Risk of burns due to accessories becoming hot
duringoperation.
• Risk of personal injury due to prolongeduse.
SAVE THESE INSTRUCTIONS
Chargers
DeWALT chargers require no adjustment and are designed to be
as easy as possible tooperate.
Electrical Safety
The electric motor has been designed for one voltage only.
Always check that the battery pack voltage corresponds to the
voltage on the rating plate. Also make sure that the voltage of
your charger corresponds to that of yourmains.
i
Your DeWALT charger is double insulated in
accordance with IEC60335; therefore, no earth wire
isrequired.
If the supply cord is damaged, it must be replaced only by
DeWALT or an authorised serviceorganisation.
Using an Extension Cable
An extension cord should not be used unless absolutely
necessary. Use an approved extension cable suitable for the
power input of your charger (refer to Technical Data). The
minimum conductor size is 1mm
2
; the maximum length is30m.
When using a cable reel, always unwind the cablecompletely.
Important Safety Instructions for All
BatteryChargers
SAVE THESE INSTRUCTIONS: This manual contains important
safety and operating instructions for compatible battery
chargers (referto TechnicalData). Before using charger, read all
instructions and cautionary markings on charger, battery pack, and
product using batterypack.

WARNING: Shock hazard. Do not allow any liquid to get
inside charger. Electric shock mayresult.

WARNING: We recommend the use of a residual current
device with a residual current rating of 30mA orless.

CAUTION: Burn hazard. To reduce the risk of injury,
charge only DeWALT rechargeable batteries. Other types of
batteries may burst, causing personal injury anddamage.