DeWalt DCR017 - Assembly and Operation Basics; Mains Plug Replacement (U.K. & Ireland); Using an Extension Cable; Inserting a Battery Pack

8
ENGLISH
ASSEMBLY AND ADJUSTMENTS

WARNING: Use only
DeWALT
battery packs andchargers.
Inserting a Battery Pack(Fig.A,C)
NOTE: Make sure your battery pack is fully charged. If the
battery pack does not produce sufficient power, charge the
battery pack following the instructions in the manual of
thecharger.
NOTE: To ensure maximum performance and life of Li-Ion
batteries, charge the battery for a minimum of 10 hours before
firstuse.
1. Release the latch
9
to open the battery compartmentcover.
2. Insert the battery pack
19
into the receptacle
10
until it is
fullyseated.
3. Close and latch the battery compartmentcover.
Fuel Gauge Battery Packs (Fig. C)
Some
DeWALT
battery packs include a fuel gauge which
consists of three green LED lights that indicate the level of
charge remaining in the batterypack.
To actuate the fuel gauge, press and hold the fuel gauge
button
20
. A combination of the three green LED lights will
illuminate designating the level of charge left. When the level
of charge in the battery is below the usable limit, the fuel gauge
will not illuminate and the battery will need to berecharged.
NOTE: The fuel gauge is only an indication of the charge left on
the battery pack. It does not indicate tool functionality and is
subject to variation based on product components, temperature
and end-userapplication.
To Install the Coin Cell Battery (Fig.A,B)

WARNING: When replacing battery, replace it with the
same brand and type. Observe correct polarity(+ and –)
when replacing batteries. Do not store or carry batteries so
that metal objects can contact exposed batteryterminals.
Your radio is equipped with memory capacity in order to store
the time and your selected memory channels. When the radio is
OFF, this memory capacity is powered by one coin cell battery
that is included with theradio.
1. Turn the charger/radio off and unplug from the
powersource.
2. Open the battery compartment by lifting the battery
compartment latch
9
.
3. Unscrew the screw
18
on the battery door
12
.
4. Press down on the battery door latch and pull toopen.
5. Install the coin cell battery
13
according to the diagram
inside the coin cell batteryarea.
6. Replace the battery door, insert screw andtighten.
7. Securely close the batterycompartment.
NOTE: To reset the LCD display, clock and presets, remove the
coin cell battery and re-install it. Follow this procedure if the
screen seems to lock inplace.
OPERATION
Instructions for Use

WARNING: Always observe the safety instructions and
applicableregulations.

WARNING: Do not place the charger/radio in locations
where it may be exposed to dripping orsplashing.
AC Operation(Fig.D)
Unwrap power cord and plug into 110 or 230 V AC walloutlet.
Operating the Radio(Fig.A)
Power/Volume Adjustment
1. To turn the radio on, press the power button
1
.
NOTE: When the radio is first used it will enter DAB mode
and automatically scan for stations. It will then set the time
and start playing the first station it finds. If there is no time
signal available please refer to Programming the Clock to
manually set thetime.
2. Turn the dial
2
clockwise to increase the volume. To
decrease the volume, turn anti-clockwise.
Mode Selection
To choose one of the mode functions(DAB, FM, or AUX) push
the mode button
4
until the desired function is found. For
example, if the radio is on DAB, seen in upper left portion of LCD
display
8
, push the mode button twice to change toAUX.
DAB Mode - Tuning
When the unit is first switched on in DAB/DAB+ mode the radio
will auto scan to find broadcast stations in the localarea.
Use the left or right arrow buttons
3
to scroll through
thestations.
NOTE: When moving locations or if reception was poor
in the original scan(possible if the antenna was not up),
this may result in an empty or incomplete list of available
stations. Manually running an Auto Scan will find all available
broadcaststations.
To Perform an Auto Scan:
1. Press the menu button
5
, scroll through the options by
pressing the right arrow button
3
until you reach Auto
Scan and select this option by pressing the Enter/Display
button
7
.
2. Press the right arrow button to select the Yesoption.
3. Press the Enter/Display button
7
to perform the AutoScan.
Once Auto Scan is complete the radio will play the first station
itfinds.
To use presets please reference To Program the
MemoryButtons.
DAB Mode – Station Prune
Some stations once received by your radio which are no longer
available may display with a ? after the stationname.
To remove these stations from the station list, use the Prune
function:
1. Press Menu
5
and scroll right to the Pruneoption.