DeWalt DWE7492 - General Power Tool Safety Warnings; Save All Warnings and Instructions for Future Reference

23
ENGLISH
English (original instructions)

WARNING! Read all safety warnings and all instructions. Failure to follow the
warnings and instructions may result in electric shock, fire and/or seriousinjury.
WARNING: To reduce the risk of injury, read the instructionmanual.
Intended Use
DWE7492 table saw is designed for professional ripping, cross-cutting, mitering and bevelling
with various materials as wood, wood composite materials andplastics.
DO NOT use under wet conditions or in the presence of flammable liquids orgases.
DO NOT use for cutting metal, cement board, ormasonry.
DO NOT use shaping cutter heads on thissaw.
DO NOT perform tapered cuts without a tapered jigaccessory.
DO NOT use the saw for plunge or cove cutting.
These table saws are professional powertools.
DO NOT let children come into contact with the tool. Supervision is required when
inexperienced operators use thistool.
Definitions: Safety Alert Symbols and Words
This instruction manual uses the following safety alert symbols and words to alert you to
hazardous situations and your risk of personal injury or propertydamage.

DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in
death or seriousinjury.

WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in
death or seriousinjury.

CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in
minor or moderateinjury.

(Used without word) Indicates a safety relatedmessage.
NOTICE: Indicates a practice not related to personal injury which, if not avoided, may
result in propertydamage.
GENERAL POWER TOOL SAFETY WARNINGS

WARNING: Read all safety warnings, instructions, illustrations and specifications
provided with this power tool. Failure to follow all instructions listed below may result in
electric shock, fire and/or seriousinjury.
SAVE ALL WARNINGS AND INSTRUCTIONS FOR
FUTURE REFERENCE.
The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-
operated (cordless) powertool.
1) Work Area Safety
a ) Keep work area clean and well lit. Cluttered or dark areas inviteaccidents.
b ) Do not operate power tools in explosive atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools create sparks which may ignite the dust
orfumes.
c ) Keep children and bystanders away while operating a power tool. Distractions can
cause you to losecontrol.
2) Electrical Safety
a ) Power tool plugs must match the outlet. Never modify the plug in any way. Do not
use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and
matching outlets will reduce risk of electricshock.
b ) Avoid body contact with earthed or grounded surfaces, such as pipes, radiators,
ranges and refrigerators. There is an increased risk of electric shock if your body is earthed
orgrounded.
c ) Do not expose power tools to rain or wet conditions. Water entering a power tool will
increase the risk of electricshock.
d ) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the
power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged
or entangled cords increase the risk of electricshock.
e ) When operating a power tool outdoors, use an extension cord suitable for outdoor
use. Use of a cord suitable for outdoor use reduces the risk of electricshock.
f ) If operating a power tool in a damp location is unavoidable, use a ground
fault circuit interrupter (GFCI) protected supply. Use of a GFCI reduces the risk of
electricshock.
3) Personal Safety
a ) Stay alert, watch what you are doing and use common sense when operating a
power tool. Do not use a power tool while you are tired or under the influence of
drugs, alcohol or medication. A moment of inattention while operating power tools may
result in serious personalinjury.
b ) Use personal protective equipment. Always wear eye protection. Protective
equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for
appropriate conditions will reduce personalinjuries.
c ) Prevent unintentional starting. Ensure the switch is in the off-position before
connecting to power source and/or battery pack, picking up or carrying the tool.
Carrying power tools with your finger on the switch or energizing power tools that have the
switch on invitesaccidents.
d ) Remove any adjusting key or wrench before turning the power tool on. A wrench or a
key left attached to a rotating part of the power tool may result in personalinjury.
e ) Do not overreach. Keep proper footing and balance at all times. This enables better
control of the power tool in unexpectedsituations.
f ) Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and
gloves away from moving parts. Loose clothes, jewelry or long hair can be caught in
movingparts.
g ) If devices are provided for the connection of dust extraction and collection facilities,
ensure these are connected and properly used. Use of dust collection can reduce dust-
relatedhazards.
h ) Do not let familiarity gained from frequent use of tools allow you to become
complacent and ignore tool safety principles. A careless action can cause severe injury
within a fraction of asecond.
4) Power Tool Use and Care
a ) Do not force the power tool. Use the correct power tool for your application. The
correct power tool will do the job better and safer at the rate for which it wasdesigned.
b ) Do not use the power tool if the switch does not turn it on and off. Any power tool that
cannot be controlled with the switch is dangerous and must berepaired.
c ) Disconnect the plug from the power source and/or remove the battery pack,
if detachable, from the power tool before making any adjustments, changing
accessories, or storing power tools. Such preventive safety measures reduce the risk of
starting the power toolaccidentally.
d ) Store idle power tools out of the reach of children and do not allow persons
unfamiliar with the power tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrainedusers.
e ) Maintain power tools and accesories. Check for misalignment or binding of moving
parts, breakage of parts and any other condition that may affect the power tool’s
operation. If damaged, have the power tool repaired before use. Many accidents are
caused by poorly maintained powertools.
f ) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting
edges are less likely to bind and are easier tocontrol.
g ) Use the power tool, accessories and tool bits etc. in accordance with these
instructions, taking into account the working conditions and the work to be
performed. Use of the power tool for operations different from those intended could result
in a hazardoussituation.
h ) Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery
handles and grasping surfaces do not allow for safe handling and control of the tool in
unexpectedsituations.
5) Service
a ) Have your power tool serviced by a qualified repair person using only identical
replacement parts. This will ensure that the safety of the power tool ismaintained.
Safety Instructions for Table Saws
1) Guarding Related Warnings
a ) Keep guards in place. Guards must be in working order and be properly mounted. A
guard that is loose, damaged, or is not functioning correctly must be repaired orreplaced.
b ) Always use saw blade guard, riving knife and anti-kickback pawls for every
through-cutting operation. For through-cutting operations where the saw blade cuts
completely through the thickness of the workpiece, the guard and other safety devices help
reduce the risk ofinjury.
c ) Immediately reattach the guarding system after completing an operation (such
as rabbeting cuts) which requires removal of the guard, riving knife and/or anti-
kickback device. The guard, riving knife, and anti-kickback device help to reduce the risk
ofinjury.
d ) Make sure the saw blade is not contacting the guard, riving knife or the workpiece
before the switch is turned on. Inadvertent contact of these items with the saw blade
could cause a hazardouscondition.
e ) Adjust the riving knife as described in this instruction manual. Incorrect spacing,
positioning and alignment can make the riving knife ineffective in reducing the likelihood
ofkickback.
f ) For the riving knife and anti-kickback pawls to work, they must be engaged in the
workpiece. The riving knife and anti-kickback pawls are ineffective when cutting workpieces
that are too short to be engaged with the riving knife and anti-kickback pawls. Under these
conditions a kickback cannot be prevented by the riving knife and anti-kickbackpawls.
g ) Use the appropriate saw blade for the riving knife. For the riving knife to function
properly, the saw blade diameter must match the appropriate riving knife and the body of
the saw blade must be thinner than the thickness of the riving knife and the cutting width of
the saw blade must be wider than the thickness of the rivingknife.