DeWalt ToughSystem DWST1-75663 - DAB+ OPERATION; DAB+ MENU; Stations List; Setting Favorites (Presets)

11
ENGLISH
Finding a desired frequency can be performed in one of two
methods: Auto Scan or ManualTune.
Auto Scan
1. Press the audio source button
 
until the required source
isreached.
2. Press the selection dial
20
to enter the Main Menu (see
GeneralSetup).
3. Rotate the selection dial clockwise until Auto Scan is
reached and press to select. The Auto Scan begins searching
for the closest strong, clearsignal.
‑ Rotate the dial clockwise to scan up thefrequencies.
‑ Rotate the dial counterclockwise to scan down
thefrequencies.
4. Once a desired frequency is found, save it to one of the
channel preset buttons (see Setting the PresetButtons).
Manual Tune
1. Select the required audio source and enter the Main Menu
(see GeneralSetup).
2. Rotate the selection dial
20
clockwise and press it to select
ManualTune.
3. Rotate the selection dial clockwise to go up the frequencies
or counterclockwise to go down the frequencies, until the
desired frequency isreached.
4. Once a desired frequency is found, save it to one of the
channel preset buttons (see Setting the PresetButtons).
Setting FM Presets
1. Set the radio to the desired station/frequency (see Auto
Scan or ManualTune).
2. Press and hold the desired preset button
 
until
a message >> P# is displayed. The station is saved to the
displayed preset button number (#).
3. Repeat steps 1and 2to set additional presetstations.
4. Press the back button
 
to return to the Audio
Sourcescreen.
5. The selected station is indicated on the LCD screen (button
2in theexample).
DAB+ OPERATION
1. When first turned on or after restoring to default settings,
the appliance will automatically run a full station scan to find
broadcasting stations.
2. Use the selection dial
20
to scroll through thestations.
DAB+ MENU
Full Scan
1. Press the Selection Dial
20
, and turn it to browse through
themenu.
2. When Full Scan is chosen, the appliance will run a full band
scan, displaying the number of stations found.
3. When complete, the appliance will play the first station on
the band.
Stations List
When selected, the appliance will display the full list of available
stations. Browse the list using the selection dial
20
and press to
select astation.
NOTE: When moving locations or if reception was poor in the
original scan, this may result in an empty or incomplete list of
available stations. Manually running an Full Scan will find all
available broadcast stations.
Setting Favorites (Presets)
1. Set the radio to the desired station (see FullScan).
2. Press and hold the desired preset button
 
until
a message >> P# is displayed. The station is saved to the
displayed preset button number (#).
3. The selected station is indicated on the LCDscreen.
Information Display
The following information can be selected to be displayed
onscreen:
Scrolling Text – loop through all types of information,
3seconds each.
Frequency - the playing station's frequency.
Type - the type of media broadcast made by the currentstation.
Data rate - the resolution that is broadcast by the station.
NOTE: The information is provided by the stations, and not
controlled by theappliance.
DAB Settings
1. Prune stations - Some stations previously received by your
radio that might no longer be available will display blanks in
place of the station name. To remove these stations from the
station list press the Selection Dial
20
. You will be asked to
confirm your choice (similar to “Restore toDefault”).
2. DRC (dynamic range compression) - This function
reduces the difference between the loudest and quietest
audio being broadcast. Effectively, this makes quiet sounds
comparatively louder, and loud sounds comparatively
quieter. The following options are available:
‑ DRC off
‑ DRC low
‑ DRC high
NOTE: DRC only works if it is enabled by the broadcaster
Important Radio Notes
1. Reception will vary depending on location and strength of
radiosignal.
2. Running the radio while connected to certain generators
may cause backgroundnoise.
Adjusting the Sound Preferences
Sound preferences can be adjusted by changing the
equalization of the Bass, Treble orMid.
1. Press the selection dial
20
.
2. Rotate the selection dial clockwise until Main Menu
isreached.
3. Press the selection dial to access the MainMenu.