To Turn On The Engine Using The
ENGINE START/STOP Button —
Automatic Transmission Only
1. The transmission must be in PARK.
2. Press and hold the brake pedal while pushing the
ENGINE START/STOP button once.
3. If the vehicle fails to start, the starter will disengage
automatically after 10 seconds.
4. If you wish to stop the cranking of the engine prior to
the engine starting, push the ENGINE START/STOP
button again.
NOTE:
Normal starting of either a cold or a warm engine is
obtained without pumping or pressing the accelerator
pedal.
To Turn Off The Engine The Using
ENGINE START/STOP Button — Manual
Transmission Only
1. With the vehicle stopped, place the gear selector in
NEUTRAL, then push and release the ENGINE
START/STOP button.
2. The ignition will return to the OFF position.
3. Place the gear selector in FIRST gear or REVERSE
and then apply the parking brake.
NOTE:
•
If the ignition switch is left in the ACC position, the
system will automatically time out after 30 minutes
of inactivity and the ignition will switch to the OFF
position.
•
If the ignition switch is left in the RUN position, the
system will automatically time out after 30 minutes
of inactivity if the vehicle speed is 0 mph (0 km/h)
and the engine is not running.
•
If the vehicle speed is above 5 mph (8 km/h), the
ENGINE START/STOP button must be held for two
seconds or three short pushes in a row before the
engine will shut off. The ignition switch position will
remain in the ACC position until the vehicle is
stopped, placed in park and the button is pushed
twice to the OFF position.
To Turn Off The Engine Using The
ENGINE START/STOP Button —
Automatic Transmission Only
1. Place the gear selector in PARK, then push and
release the ENGINE START/STOP button.
2. The ignition will return to the OFF position.
3. If the gear selector is not in PARK, the ENGINE
START/STOP button must be held for two seconds or
three short pushes in a row with the vehicle speed
above 5 mph (8 km/h) before the engine will shut
off. The ignition will remain in the ACC position until
the gear selector is in PARK and the button is
pushed twice to the OFF position. If the gear selec-
tor is not in PARK and the ENGINE START/STOP but-
ton is pushed once, the instrument cluster will dis-
play a “Vehicle Not In Park” message and the
engine will remain running. Never leave a vehicle
out of the PARK position, or it could roll.
NOTE:
If the ignition switch is left in the ACC or RUN (engine
not running) position and the transmission is in PARK,
the system will automatically time out after 30 minutes
of inactivity and the ignition will switch to the OFF
position.
AUTOPARK
AutoPark is a supplemental feature to assist with plac-
ing the vehicle in PARK should the situations on the
following pages occur. It is a back up system and
should not be relied upon as the primary method by
which the driver shifts the vehicle into PARK.
The conditions under which AutoPark will engage are
outlined on the following pages.
WARNING!
•
Driver inattention could lead to failure to place the
vehicle in PARK. ALWAYS DO A VISUAL CHECK that
your vehicle is in PARK by verifying that a solid (not
blinking) “P” is indicated in the instrument cluster
display and on the gear selector. If the “P” indica-
tor is blinking, your vehicle is not in PARK. As an
added precaution, always apply the parking brake
when exiting the vehicle.
•
AutoPark is a supplemental feature. It is not
designed to replace the need to shift your vehicle
into PARK. It is a back up system and should not
be relied upon as the primary method by which the
driver shifts the vehicle into PARK.
STARTING AND OPERATING 65
4
5548538-23_LA_OM_EN_USC_t_E2.pdf 65 4/7/2023 2:38:36 PM
To Next Page
Loading...
