DoorKing 8054 MicroPlus - Door King 8054 Receiver Programming Functions; Master Code Setup; Add Transmitter Codes; Delete Transmitter Codes

4.1 MASTER CODE
1. Press and release the MASTER CODE button on the side of
the receiver
case.
2. Enter a four digit code g-I LI and then press EI (beep).
4.2 ADD A TRANSMITTER(S)
1. Press r.:::Jl:!JL[I and the four digit master code GlG1G1GJ (beep).
2. Enter the two digit button number QQ that the recaiver is to
respond to, then press EI (beep).
Button 1 enter rDIIJ
Button 2 enter I]E]
Button 3 enter tE:E
Buttons 1&2 together enterGlD
Buttons 2&3 together enter
l!ll!I
Buttons 1 &3 together enter IClEJ
3. Enter the four digit facility code (J"'--::;;:""'II-""'IJ""-I. then press EI (beep).
Valid facility code numbers are: 0000 - 4095
4. Enter the five digit beginning transmitter number
I-I:!-I:II I-I then press EI (beep).
5. Enter the five digit ending transmitter number QGl-lt-IQ then
press EI (beep).
Valid transmitter numbers are: 00000 - 65407
If programming a single transmitter, the beginning and ending
transmitter number will be the same.
6. Enter the time zone number g then press EI (beep).
Valid time zone numbers are: 0 - 9
There are
10 available time zones, however only time zones
2 - 9 are programmable (see 4.7). Entering I]J in step
6
will cause the receiver to never allow access for the
transmitter(s)
being programmed, while entering m in
step six
will always allow access to the transmitters
being programmed.
When programming a block of transmitter numbers, the
receiver
will emit a short beep every 3 seconds. Wait
until this beeping stops before proceeding with any
other programming. This
may take up to 5 minutes
depending on the memory size and the number of
transmitters
being programmed.
7. Repeat steps 2 - 7 to enter additional transmitter numbers or
blocks of numbers, or press m together, or wait 20
seconds to
end the programming sequence (beep).
4.3 DELETE A TRANSMITTER
1. Press I:!JllEI and the four digit master code I ]-U-I (beep).
2. Enter the two digit button number QQ then press EI (beep).
3. Enter the four digit facility code go. IQ, then press (beep).
4. Enter the five digit transmitter number g • IGI-I then press
EI (beep).
5. Repeat steps 2-4 to delete another transmitter, or press m
together or wait 20 seconds to end the programming
sequence
(beep).
4.4 DELETE ALL TRANSMITTERS
1. Press EIIII!!J and the four digit master code GJIOJG.JG] (beep).
2. Enter It!l!EE then press EI (beep).
This sequence will take about 1 1/2 minutes. The receiver will
sound a short beep about every 3 seconds, then one
long beep when the deletion is complete.
4.5 RELAY STRIKE
TIME
1. Press r.:::I'!:2l!l and the four digit master code 1-IUrn (be~).
2. Enter the dasired strike time in seconds GJGJ then press EI
(beep).
Valid strike timas are: 01 - 99
3. Press rnm together or wait 20 seconds to end the
programming sequence (beep).
4.6 PROGRAMMING TIME & DAY
1. Press and the four digit master code w-m:II;1 (beep).
2. Enter the current hour and minute I-I-no then press EI
(beep).
3. Enter I]J for AM orm for PM then press EI (beep).
4. Enter the current month then press EI (beep).
5. Enter the current day of the month GJGJ then press EI (beep).
6. Enter the last two digits of the current year GJGJ then
press EI (beep).
7. Enter the day of the week g then press EI (beep).
1 = Sunday, 7 == Saturday
8. Press m together or wait 20 seconds to end the
programming sequence (beep).
4.7 TIME ZONES
1. Press r.::Jl!J!!] and the four digit master code (beep).
2. Enter the time zone number to be programmed g then
press
EI (beep).
Valid time zone numbers are: 2 - 9
3. Enter the beginning time in hours and minutas lDt-n-1Q then
prass EI (beep).
4. Enter I]J for AM or m for PM then press EI (beep).
5. Enter the ending time in hours and minutes Glt-R I-I then
press EI (beep).
6. Enter I]J for AM or m for PM then press EI (beep).
7. Enter the !ays of the week that the time zone is active
g IA-lmrJ then press EI (beep).
Use the # key to skip days. For example, if the time zone is
ective
Mcm~ through Friday only, enter:
[! m 3' 4 filI!I!lL!J
8. fiE!e.eat steps 2 - 7 to program additional time zones, or press
[[J[!I together or walt 20 seconds to end the
programming sequence (beep).
4.8 PRINT MODE
1. Press!L:Jl.!llIl and the four digit master code (beep).
2. Enter m to print transactions in real time mode or enter I]J to
not print
the transactions In real tima mode, then press
EI (beep).
In either case, transactions are stored in the buffer and can be
printed later.
If programming for real time print mode, printer
must be connected and turned ON, otherwise the
receiver
will sound four long beeps.
3. Press m together or wait 20 seconds to end the
programming sequence (beep).
4.9 CLEAR TRANSACTION BUFFER
1. Press and the four digit master code ~~.;J (beep).
2. Enter li919@91
9
1then press EI (beep).
This sequence will take about 5 minutes. The receiver will
sound a short beep about every 3 seconds, then one
long beep when the deletion is complete.
4.10
PRINT TRANSACTION BUFFER
1. Press Ii.:E.Im and the four digit master code GJQGlQ (beep).
The transactions stored in the buffer will print. The recei', Jr
will sound a long tone when complete.
4.11 PRINT TRANSACTION FOR REQUESTED DATE
1. Press EJlt!Il!I and the four digit master code FI_'lFI_"""I["'IlII"""_1 (beep).
2. Enter the month rn then press EI (beep).
3. Enter the day IG]G'J then press EI (beep).
The transactions for the requested date will print. The
receiver
will sound a long tone when complete.