PG9949/PG8949/PG4949
PowerG 2-Button Wireless Key
Installation Instructions
WARNING!
Choking Hazard; Small parts; The pendant and belt
clip are NOT for children under 3 years
Do not submerge the wireless key in any liquid as it
will damage the electronic circuits. Keep this manual for future
reference.
Operation
The PGx949 is a programmable 2-button wireless key. The
PGx949 can be configured to transmit up to three separate com-
mands to the alarm system. Two of the commands are transmit-
ted by pressing one of the buttons separately, and the third is by
pressing them simultaneously. Confirmation of a successful
transmission is indicated by the LED light.
Default Settings
Arm {button 1) - Press for 1 second
Disarm (button 3) - Press for 1 second.
Panic (button 4) - Press and hold both buttons for more than 3
seconds.
Device Setup
Enrollment
To quick enroll:
1. On a keypad press [*] [8] [Installer Code]
[804] [000].
2. Press and hold the [ ] button on the wire-
less key until the LED lights steady and then release the
[ ] button while the LED is still lit and a confirmation
message appears on the keypad.
3. Press [*] on the keypad to confirm the device ID.
4. Enter [3 digit wireless key #]
5. Assign the wireless key to a partition by entering the [three
digit partition #].
6. To assign the wireless key to a user enter the [3 digit user #].
To pre-enroll:
1. Remotely configure the unique ID number into the system.
For more information see the HSM2HOST manual.
2. When on-site, press the button on the wireless key.
Programming Buttons
The buttons are programmable.
To change button programming:
1. From a keypad enter [*] [8] [Installer Code] [804][601] to
[632].
2. Configure button 1 (default arm) using the table below.
Enter the desired two digit option.
3. Configure button 3 (default disarm) by entering the desired
two digit option.
4. Configure button 4 (both buttons pressed simultaneously) by
entering the desired two digit option.
Configuration
To enter the wireless configuration section enter [804][601].
Device Toggles
Assembly
Attaching to a Belt Clip
1. Slide the device into the holder until you feel it snap
securely inside.
2. To attach the belt clip, slide it onto the rails on the rear of the
holder.
Mounting
1. Align the holder on a wall facing up as illustrated.
2. Using two #4 5/8” screws and
appropriate wall anchors, secure
the holder to the wall
3. Slide the device into the holder
until you feel it snap securely
inside.
Maintenance
Warning! Modifications to this wire-
less key not expressly approved by the
party responsible for compliance may
void the user’s authority to operate it.
Replacing the Battery
The required battery is CR2032 Lithium 3V, manufactured by
VARTA or Energizer, purchased from a DSC-approved sup-
plier.
When this wireless key is out of use, remove all batteries and
dispose of them separately. Bring electrical appliances to the
local collecting points for waste electrical and electronic equip-
ment. Batteries are harmful to the environment, please help to
protect the environment from health risks.
Replace the battery at least once every 5 years, or upon observ-
ing that the LED flickers when transmitting.
NOTE: The polarity of the battery must be observed. Improper
handling of lithium batteries may result in heat generation,
explosion or fire, which may lead to personal injuries.
WARNING: Danger of explosion if batteries are installed
incorrectly. Replace only with the same or equivalent type rec-
ommended by the manufacturer. Keep away from small chil-
dren. If batteries are swallowed, promptly see a doctor. Do not
try to recharge these batteries. Disposal of used batteries must
be made in accordance with the waste recovery and recycling
regulations in your area.
1. To replace the battery, insert a coin into the slot on the bot-
tom of the unit and twist it open.
Note: Make sure the elastic pad within the cover remains in
place. Put it back in place if it falls off.
2. Extract the old battery from its holder, and replace it with a
recommended new battery. Ensure that the plus side of the
battery faces up, attaining correct polarity.
3. Test the device by pressing the button. The LED indicator
should light.
4. Reattach the cover securely, verifying that the cover snaps
shut.
Cleaning
The use of abrasives of any kind and solvents such as ker-
osene, acetone or thinner is strictly forbidden.
Clean the wireless key only with a soft cloth or sponge moist-
ened lightly with a mixture of water and mild detergent, and
wipe it dry immediately.
Testing
Always test the system at least once per a year.
1. Ensure the device is enrolled in the system.
2. Stand 3 m (10 ft) away from the control panel and press the
button. Verify that the transmit LED lights and the control
panel responds as programmed.
3. Operate the pendant from various locations within the area
covered by the receiver to determine "dead" locations,
where transmission is blocked by walls and large objects, or
affected by structural materials.
Note: If dead/marginal zones are a problem, relocating the
receiver may improve the performance.
Specifications
Frequency Band (MHz): CE Listed PG4949: 433-434MHz;
CE/EN listed PG8949: 868MHz; FCC/IC/UL/ULC listed
PG9949: 912-919MHz
Communication Protocol: PowerG
Battery type: For UL/ULC listed installation use only Varta or
Energizer 3V CR-2032 Lithium battery consumer grade
Battery Life Expectancy: 5 years
(not verified by UL/ULC)
Low Battery Threshold: 2.05 V
Note: If transmission is still possible despite the battery condi-
tion, the unit will send a low battery signal to the control panel.
Temperature Range: -10°C to +55°C (UL/ULC only verified
the range 0ºC-49ºC)
Humidity: up to max. 93%RH, non-condensing
Dimensions (LxWxD): 53 x 33 x 11 mm (2.1 x 1.3 x 0.43 in)
Weight: 15 g (0.5 oz)
Weight (including battery): 20 g (0.7 oz)
Note: To be used in non-hazardous locations only.
Compatible Receivers
433MHz Band: HSM2HOST4; HS2LCDRF(P)4;HS2IC-
NRF(P)4; PG4920
868MHz Band: HSM2HOST8; HS2LCDRF(P)8; HS2IC-
NRF(P)8;PG8920
912-919MHz Band: HSM2HOST9; HS2LCDRF(P)9; HS2IC-
NRF(P)9; PG9920
Note: Only devices operating in band 912-919MHz are UL/
ULC listed.
UL/ULC Notes
Only model PG9949 operating in the frequency band 912-
919MHz is UL/ULC listed. The PG9949 has been listed by UL
for commercial and residential burglary applications and by
ULC for residential burglary applications in accordance with
the requirements in the Standards UL1610/UL1023/ULC-
ORD-C1023 and ANSI/SIA CP-01-2010 Control Panel
Standard – Features for False Alarm Reduction.
Note: For UL commercial burglary applications:
• After arming the system via the wireless key the user should verify the
closing confirmation has been indicated at the keypad.
• Panic button must be disabled.
For UL/ULC installations use these device only in conjunction
with compatible DSC wireless receivers: HSM2HOST9,
HS2LCDRF(P)9, HS2ICNRF(P)9 and PG9920. After
installation verify the product functionality in conjunction with
the compatible receiver used.
Europe: The PG4949 and PG8949 are compliant
with the RTTE requirements - Directive 1999/5/EC
of the European Parliament and of the Council of 9
March 1999. The PG8949 is certified by Telefica-
tion to the following standards: EN50131-3, EN50131-1
GRADE 2, CLASS II, EN50131-6 Type C. Telefication BV
has certified only the 868 MHz variant of this product. Accord-
ing to EN 50131-1:2006 and A1:2009, this equipment can be
applied in installed systems up to and including Security Grade
2, Environmental Class II. UK: The PG8949 is suitable for use
in systems installed to conform to PD6662:2010 at Grade 2 and
environmental class 2 BS8243. The Power G peripheral devices
have two- way communication functionality, providing addi-
tional benefits as described in the technical brochure. This
functionality has not been tested to comply with the respective
technical requirements and should therefore be considered out-
side the scope of the product’s certification
FCC COMPLIANCE STATEMENT
WARNING! Changes or modifications to this unit not
expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
This device has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protec-
tion against harmful interference in residential installations.
This equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio and tele-
vision reception.
However, there is no guarantee that interference will not occur
in a particular installation. If this device does cause such inter-
ference, which can be verified by turning the device off and on,
the user is encouraged to eliminate the interference by one or
more of the following measures:
– Re-orient or re-locate the receiving antenna.
– Increase the distance between the device and the receiver.
– Connect the device to an outlet on a circuit different from the
one that supplies power to the receiver.
– Consult the dealer or an experienced radio/TV technician.
This equipment complies with FCC and IC RF radiation expo-
sure limits set forth for an uncontrolled environment.
This device complies with FCC Rules Part 15 and with Industry
Canada licence-exempt RSS standard(s). Operation is subject
to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any inter-
ference that may be received or that may cause undesired oper-
ation.
Le present appareil est conforme aux CNR d'Industrie Canada
applicables aux appareils radio exempts de licence.
L'exploitation est autorisee aux deux conditions suivantes :(1)
l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur
de l'appareil doit accepter tout brouillage radioelectrique subi,
meme si le brouillage est susceptible d'en compromettre le
fonctionnement.
PG9949/PG8949/PG4949
PowerG ৼ᤹䫞ᰐ㓯䫕ᆹ㻵ᤷই
䆖ʽ
ヂড䲙˗ሿ䜘Ԧ˗䚕᧗䫕઼Ⳟᑖཀྵн䘲 3
ԕлݯㄕ⧙㘽
⾱→ሶᰐ㓯䫕㖞Ҿԫօ⏢փѝˈ ࡉՊᦏൿ
⭥䐟DŽ 䈧؍⮉ᵜˈԕׯሶᶕ৲㘳DŽ
PGx949 ᱟ䇮㖞Ⲵৼ᤹䫞ᰐ㓯䫕DŽ ൘䘋㹼ᓄⲴ䝽㖞
ˈ PGx949 ᴰཊᣕ䆖㌫㔏ࠪйᶑнⲴભԔDŽ ࠶
࡛᤹лєњ᤹䫞ˈቡԕࠪєᶑભԔˈ㘼ᰦ᤹лєњ
᤹䫞ˈԕࠪㅜйᶑભԔDŽ 䙊䗷 LED ⚟ᤷ⽪ԕ⺞䇔ᱟ
䘱ᡀ࣏DŽ
唈䇔䇮㖞
ᐳ䱢 { ᤹䫞 1) - ᤹տ ᒦ؍ᤱ 1 。䫏
䱢 { ᤹䫞 3) - ᤹տ ᒦ؍ᤱ 1 。䫏DŽ
ᓄᙕᴽ࣑ ( ᤹䫞 4) - ᤹տєњ᤹䫞ᒦ؍ᤱ 3 。䫏ԕкDŽ
䇮༷ᆹ㻵
⌘
ᘛ䙏⌘ :
1. ൘䭞ⴈк᤹ [*] [8] [ ᆹ㻵Ӫઈԓ⸱ ] [804]
[000]DŽ
2. ᤹лᰐ㓯䫕кⲴ [] ᤹䫞ˈⴤࡠ LED
⚟っᇊӞˈ❦൘ LED ӽ❦ӞⲴᰦىᶮᔰ []᤹
䫞ˈ↔ᰦ䭞ⴈкሶᱮ⽪аᶑ⺞䇔⎸DŽ
3. ᤹л䭞ⴈкⲴ [*]ˈሩ䇮༷ ID 䘋㹼⺞䇔DŽ
4. 䗃ޕ [3 սᮠⲴᰐ㓯䭞 #]
5. 䗃ޕ䘉њ [3 սᮠⲴᆀ㌫㔏 #]ˈѪᰐ㓯䫕࠶䝽ᆀ㌫
㔏DŽ
6. 䗃ޕ [3 սᮠⲴ⭘ᡧ #]ˈሶᰐ㓯䫕࠶䝽㔉⭘ᡧDŽ
亴⌘ :
1. ሶୟаⲴ ID 䘌〻䝽㖞ࡠ㌫㔏ѝDŽ ᴤཊ䈖ᛵˈ䈧৲䰵
HSM2HOST DŽ
2. ൘⧠൪ᰦˈࡉ᤹ᰐ㓯䫕кⲴ᤹䫞DŽ
᤹䫞䇮㖞
䘉Ӌ᤹䫞ᱟ䇮㖞ⲴDŽ
ྲ䴰ᴤ᭩᤹䫞Ⲵ䇮㖞 :
1. ൘䭞ⴈк᤹ [*] [8] [ ᆹ㻵Ӫઈԓ⸱ ] [804][601] 㠣
[632]DŽ
2. ֯⭘л㺘ሩ 1 ᤹䫞䘋㹼䝽㖞 ( 唈䇔䇮㖞Ѫᐳ䱢 )DŽ 䗃
ޕ䴰㾱Ⲵєսᮠ䘹亩DŽ
3. 䙊䗷䗃ޕ䴰㾱Ⲵєսᮠ䘹亩ˈሩ 3 ᤹䫞䘋㹼䝽㖞DŽ
4. 䗃ޕ䴰㾱Ⲵєսᮠ䘹亩ˈሩ 4 ᤹䫞 ˄ᰦ᤹лєњ
᤹䫞˅䘋㹼䝽㖞DŽ
䝽㖞
ྲ㾱䘋ޕᰐ㓯䝽㖞⇥ˈ䈧䗃ޕ [804][601]DŽ
䇮༷࠷ᦒ
㻵䝽
䘎᧕Ⳟᑖཀྵ
1. ሶ䇮༷━ޕᓗˈⴤࡠࡠசంа༠⢒⢒㍗DŽ
2. ྲ䴰䘎᧕Ⳟᑖཀྵˈሶަ━ޕᓗ䶒Ⲵሬ䖘кDŽ
ᆹ㻵
1. ሶᓗ䶒ᵍк᭮൘້кˈྲമᡰ⽪DŽ
2. ֯⭘єњ 4 5/8” Ⲵ㷪䪹઼
ᓄⲴ㟘㛰㷪ṃˈሶᓗപᇊ൘້
кDŽ
3. ሶ䇮༷━ޕᓗˈ ⴤࡠࡠசం
а༠⢒⢒㍗DŽ
㔤ᣔ
䆖 ! ᵚᖱᗇ䍏䍓㿴ᙗⲴаᯩⲴ
᰾⺞䇨ˈ 㠚ሩᵜᰐ㓯䫕䘋㹼
ᴤ㜭ሬ㠤⭘ᡧⲴ֯⭘ᵳ䲀ཡ
᭸DŽ
ᴤᦒ⭥⊐
䴰㾱֯⭘Ⲵ⭥⊐Ѫ VARTA ᡆ Energizer ࡦ䙐ˈӾ DSC 䇔
Ⲵᓄ୶༴䍝ҠⲴ CR2032 3V 䬲⭥⊐DŽ
ྲ↔䚕᧗䫕ᓏᔳˈ䈧ࠪᡰᴹ⭥⊐ˈ❦࠶࡛ሩᆳԜ
䘋㹼༴⨶DŽ ሶ⭥≄䇮༷䘱ࡠᖃൠᓏᰗ⭥≄઼⭥ᆀ䇮༷എ᭦
⛩DŽ ⭥⊐ሩ⧟ຳᴹᇣˈѪҶڕᓧˈ䈧؍ᣔ⧟ຳDŽ
䈧㠣ቁӄᒤᴤᦒа⅑⭥⊐ˈᡆ㘵൘䘱ؑᰦ㿲ሏ LED ⚟
ᱟ䰚⛱DŽ
00 Disabled 16 Quick Exit
01 Disarm 17 Arm Interior
02 Instant Stay Arm 21 Comm. Output 1
03 Stay Arm 22 Comm. Output 2
04 Away Arm 23 Comm. Output 3
05 [*][9] No Entry 24 Comm. Output 4
06 Chime On/Off 29 Bypass Group Recall
07 System Test 33 Bypass Recall
09 Night Arm 51 Aux. Alarm
12 Global Stay Arm 52 Panic
13 Global Away Arm
14 Global Disarm
[011][01]
Supervision - Default [N]
Enables supervision of the device.
+
00
⾱⭘
16
ᘛ䙏ཆࠪ
01
䱢
17
䜘ᐳ䱢
02
ণᰦ⮉ᆸᐳ䱢
21
䙊ؑ 䗃ࠪ 1
03
⮉ᆸᐳ䱢
22
䙊ؑ 䗃ࠪ 2
04
ᔰᐳ䱢
23
䙊ؑ 䗃ࠪ 3
05
[*][9] ⾱→䘋ޕ
24
䙊ؑ 䗃ࠪ 4
06
䰘䫳 On/Off˖
29
ᯱ䐟㓴⎸
07
㌫㔏⍻䈅
33
ᯱ䐟⎸
09
ཌ䰤ᐳ䱢
51
䖵ࣙ ᣕ䆖
12
ޘተ⮉ᆸᐳ䱢
52
ᓄᙕᴽ࣑
13
ޘተᔰᐳ䱢
14
ޘተ䱢
[011][01]
ⴁ᧗ - 唈䇔٬ [N]
⭘䇮༷Ⲵⴁ᧗࣏㜭DŽ
To Next Page
Need help?
General
