DT Research SA3000P User Manual

SA3000P/ SA3000T
ENGLISH
2
3
ENGLISH
VESA Mounng Bracket Installaon Guide for SA3000P/ SA3000T
The DT Research Signage Appliance package includes a VESA-compliant mounng bracket (1)
which mounts the SA3000P/ SA3000T (2) onto a VESA-compable monitor or display.
NOTE: The VESA Mounng Bracket is compable with most displays and monitors that support
the VESA standard.
Step1:
Locate the exisng mounng holes on the monitor. •
Line the bracket holes up with the holes on the back of the •
monitor, as shown to the right.
Place the screws to hold the mounng bracket in place and •
ghten the screws (do not over-ghten).
Step2:
Remove the two M3 screws (3) originally on the SA3000P/ •
SA3000T signage appliance.
Place the SA3000P/ SA3000T (2) on the bracket rail with •
the interface ports side facing downwards so that the two
mounng holes on the appliance are aligned with the
exisng holes on the rail (see picture).
Step 3:
Apply and ghten the screws into their original locaons and •
make sure that the bracket and the SA3000P/ SA3000T are
properly secured.
Memory and Storage
Depending on the base soware configuraon, the user may need only the internal flash memory
of the SA3000P/ SA3000T for user
’
s installed soware and storage. The user may also supplement
storage space with USB-based peripherals such as flash disks, disk drives, etc.
Opons
The SA3000P/ SA3000T Signage Appliance is designed to work with a range of custom and off-the-
shelf opons to enhance its applicability for various deployments.
* Internal PCI Express wireless LAN (WLAN) adapters with dipole antenna
Powering ON and OFF
The SA3000P/ SA3000T is programmed to Power On automacally when power is first applied
or re-established. There is also a Power Buon, located on the front of the SA3000P/ SA3000T.
To turn the SA3000P/ SA3000T on, push and release the Power Buon on the front bezel. The
adjacent power LED will be lit (blue), and the corresponding interface will be shown on the
display monitor.
To turn off the device, use the soware shutdown interface provided, or unplug the appliance.
In the event of system lockup, unplug or re-plug the power cable. Also, the Power Buon may
be used to perform a reset of the device. To do that, push and hold the Power Buon for at least
4 seconds. The system will shut down and all unsaved work may be lost. Pushing on the Power
Buon again will restart the device.
Server Installaon
Please refer to the corresponding User Guides for soware installaon instrucons.
Appliance Registraon
Aer turning on the SA3000P/ SA3000T for the first me, a
screen prompt is displayed for registering the player. If the
screen prompt is not shown, please follow the instrucons
below:
Press and hold
“
Control + Shi + Space
”
to exit the WCM 1.
Player soware.
Navigate to Start | Programs | DT Research | WCM Player2.
Select Register Player Again. The Player Registraon screen 3.
should appear. Fill in all fields to register. The required
informaon is marked.
Click OK to register and connect to the WebDT Signage 4.
Appliance Publish Server.
THE SA3000P/ SA3000T Signage Appliance
<1>
Rear ViewFront View
A
B
C
D
FE
G
H
Ethernet port
HDMI port
VGA port
RS232 COM port
DC-in
D
F
E
G
H
A
B
C
Audio jacks
Power buon
USB 2.0 (2)
<2>
<3>

DT Research SA3000P Specifications

General

Brand	DT Research
Model	SA3000P
Category	Media Player
Language	English