15
USING YOUR DYSON APPLIANCE
PLEASE READ THE ‘IMPORTANT SAFETY INSTRUCTIONS’ IN THIS DYSON
OPERATING MANUAL BEFORE PROCEEDING.
CARRYING THE APPLIANCE
• Carry the appliance by the main handle on the body.
• Do not press the cyclone release button or shake the appliance when carrying or
the cyclone could disengage, fall off and cause injury.
OPERATION
• Always extend the cable fully to the red tape before use.
• Plug the appliance into the mains electricity supply.
• To switch ‘ON’ or ‘OFF’ press the red power button, located as shown.
• After use: Unplug, push the cable retract button firmly until cable has
fully retracted.
• Switch 'OFF' the appliance and unplug before:
– changing tools
– removing the hose.
DUAL MODE FLOOR TOOL WITH
SUCTION CONTROL
EASY MODE
Reduced push force for effortless cleaning.
• For daily vacuuming of carpets, rugs and hard flooring.
• Your appliance is pre-set to this level of suction when you take it out of the box.
MAX MODE
Maximum suction for powerful dust and dirt removal.
• For vacuuming heavily soiled carpets, rugs and hard flooring.
• To switch to this setting, move the suction control slider on top of the cleaner
head as shown.
• CAUTION: The suction of this mode can damage delicate flooring.
Before vacuuming, check the flooring manufacturer’s cleaning
recommendations.
• If the suction power of Max mode prevents easy manoeuverability, switch to
Easy mode.
CARPETS OR HARD FLOORS
• The brush bar will always default to ‘ON’ (spinning) each time you switch the
machine ‘ON’.
• To reduce the speed of the brush bar (e.g. for delicate flooring and delicate hard
floors), pull the suction release trigger on the handle.
• The brush bar will automatically stop if it becomes obstructed. See ‘Brush bar –
clearing obstructions’.
• Before vacuuming your flooring, rugs and carpets, check the manufacturer’s
recommended cleaning instructions.
• Some carpets may fuzz if a rotating brush bar is used when vacuuming. If this
happens, we recommend pulling the suction release trigger to reduce brush
bar spin.
• The brush bar on the machine may damage some carpet types and delicate
hard flooring. If you are unsure, pull the suction release trigger to reduce brush
bar spin. Alternatively, use a Dyson hard floor tool (available as an option).
• This product has carbon fibre brushes. Take care if coming into contact with
them, as they may cause minor skin irritation. Wash your hands after handling
the brushes.
• Check the brush bar regularly and clear away any debris (such as hair).
Debris left on the brush bar may cause damage to flooring when vacuuming.
LOOKING AFTER YOUR DYSON APPLIANCE
• Do not carry out any maintenance or repair work other than that shown in this
Dyson Operating Manual, or advised by the Dyson Helpline.
• Only use parts recommended by Dyson. If you do not this could invalidate
your guarantee.
• Store the appliance indoors. Do not use or store it below 3°C (37.4°F).
Ensure the appliance is at room temperature before operating.
• Clean the appliance only with a dry cloth. Do not use any lubricants, cleaning
agents, polishes or air fresheners on any part of the appliance.
• If used in a garage, always wipe the base plate and ball with a dry cloth
after vacuuming to clean off any sand, dirt, or pebbles that could damage
delicate floors.
EMPTYING THE CLEAR BIN
• Empty as soon as the dirt reaches the level of the MAX mark – do not overfill.
• Switch ‘OFF’ and unplug before emptying the clear bin.
• To remove the cyclone and clear bin unit, push the red button on the top of the
carrying handle, as shown.
• To release the dirt, firmly push the red bin release button.
– The bin will slide down, cleaning the shroud as it goes.
– The bin base will then open.
• The bin base will not open if the red button is not pushed down fully.
• To minimise dust/allergen contact when emptying, encase the clear bin tightly in
a plastic bag and empty.
• Remove the clear bin carefully from the bag.
• Seal the bag tightly, dispose as normal.
• Close the clear bin by pushing the bin base upwards until it clicks into place.
• Push the bin base clip firmly until it clicks into position to ensure that the base is
securely sealed.
• Align the base of the clear bin with the air hose inlet and then click back
into place.
CLEANING THE CLEAR BIN (OPTIONAL)
• In the event that it is necessary to clean the clear bin:
• Remove the cyclone and clear bin and push the red bin base release button.
• Pull the silver catch behind the red bin release button and slide the clear bin off
the spine on the cyclone.
• Clean the clear bin with cold water only.
• Do not use detergents, polishes or air fresheners to clean the clear bin.
• Do not put the clear bin in a dishwasher.
• Do not immerse the whole cyclone in water or pour water into the cyclones.
• Ensure the clear bin is completely dry before replacing.
• To refit the clear bin:
– Insert the spine into the bin runner
– Push upwards until it clicks and then continue pushing until it slides home.
• Close the clear bin by pushing the bin base upwards. Ensure that the bin base
clicks and the clip is securely in place.
BLOCKAGES – THERMAL CUT-OUT
• This appliance is fitted with an automatically resetting thermal cut-out.
• If any part becomes blocked the appliance may overheat and automatically
cut-out.
• If this happens, follow the instructions below in ‘Looking for blockages’.
• NOTE: Large items may block the tools or wand inlet. If this happens, do not
operate the wand release catch. Switch ‘OFF’ and unplug. Failure to do so could
result in personal injury.
LOOKING FOR BLOCKAGES
• Switch ‘OFF’ and unplug before looking for blockages. Failure to do so could
result in personal injury.
• Leave to cool down for 1-2 hours before looking for blockages.
• Beware of sharp objects when checking for blockages.
• Clear any blockage before restarting.
• Refit all parts securely before using.
• Clearing blockages is not covered by your guarantee.
BRUSH BAR – CLEARING OBSTRUCTIONS
• If your brush bar is obstructed, it may shut ‘OFF’. If this happens you will need to
remove the brush bar as shown.
• Switch ‘OFF’ and unplug before proceeding. Failure to do so could result in
personal injury.
• Remove the brush bar by using a coin to loosen the fastener marked with a
padlock until it clicks.
• Beware of sharp objects when clearing obstructions.
• Replace the brush bar and secure it by tightening the fastener until it clicks.
Ensure it is fixed firmly before operating.
• Clearing brush bar obstructions is not covered by your guarantee.
• This product has carbon fibre brushes. Take care if coming into contact with
them, as they may cause minor skin irritation. Wash your hands after handling
the brushes.
BRUSH BAR – TROUBLESHOOTING
• If the brush bar has stopped spinning, follow the instructions above on clearing
obstructions. Alternatively, contact a Dyson expert on the Dyson Helpline or visit
the website.
DISPOSAL INFORMATION
• Dyson products are made from high grade recyclable materials.
Recycle where possible.
ONLINE SUPPORT
• For online help, general tips, videos and useful information about Dyson.
www.dyson.com/support
GUARANTEE TERMS & CONDITIONS
Please contact Ahmed Abdul Wahed Trading Co. (SA) or Jumbo Electronics Co.
Ltd (LLC)(UAE) for the terms and conditions of your guarantee.
Please keep your invoice to validate your guarantee.
1
3
2
To Next Page
Loading...
