Eaton EX 2200 RT 2U - User Manual

www.eaton.com
Installation and User Manual
Manuel d’installation et
d’utilisation
Manual de instalación y de
usuario
Manual de instalação e do
usuário
English
Français
Español
Portuguese
EX
2200 RT 2U
2200 RT 3U
3000 RT 2U
3000 RT 3U
3000 RT 3U XL
EXB RT 3U
Pulsar Series

Eaton EX 2200 RT 2U Specifications

General

Brand	Eaton
Model	EX 2200 RT 2U
Category	UPS
Language	English

Summary

Introduction

Environmental Protection and Disposal

Covers EATON's eco-design, substances, packing, and end-of-life product/battery disposal.

Important Safety Instructions

Certification Standards Compliance

Lists various certification standards the equipment complies with.

Safety of Persons and Product

Covers electrical hazards, battery handling, safe installation, and environmental precautions.

Special Precautions for Handling

Notes on handling, installation, and battery charging periods.

Symbol Usage

Operational and LED Indicator Symbols

Explains symbols for warning, information, action, audible signals, and LED states.

1. Presentation

1.1 Standard Positions

Details dimensions, weight, and part numbers for tower and rack positions.

1.2 Rear Panels

Identifies and describes connectors and ports on the rear panel of EX 2200/3000/3000 XL and EXB.

1.3 Control Panel

Details the buttons, LEDs, and LCD display on the UPS control panel.

2. Installation

2.1 Unpacking and Contents Check

Guide on how to unpack the UPS and verify all components are present.

2.2 Installation in Tower Position

Instructions for setting up the UPS in a vertical tower configuration.

2.3 Installation in Rack Position

Instructions for mounting the UPS into a standard 19-inch rack.

2.4 Communication Ports

Explains how to connect RS232/USB ports and install communication cards.

2.5 Connections with a FlexPDU Module

Steps for connecting the UPS to a FlexPDU module for power distribution.

2.6 Connections with a HotSwap MBP Module

Steps for connecting the UPS to a HotSwap MBP module for maintenance.

2.7 UPS Connection Without Optional Modules

How to connect the UPS directly to the power source and loads.

3. Operation

3.1 Start-Up and Normal Operation

Guide on initial startup, normal operation, and LED indications.

3.2 Operation on Battery Power

Explains UPS behavior during battery power, low battery, and end of backup time.

3.3 Return of AC power

Describes how the UPS behaves when AC power is restored.

3.4 UPS shutdown

Instructions on how to safely shut down the UPS.

3.5 Using the UPS Remote Control Functions

How to use RPO and ROO functions for remote control.

4. Access to Maintenance and Personalization Data

4.1 Display Organization

Overview of the UPS display structure for status, measurements, and personalization.

4.2 Access to Measurements

How to navigate the UPS menu to view measurements like voltage and current.

4.3 Personalization using the control panel

Steps to personalize UPS settings like language and audio alarm via the control panel.

Output Personalization

Details on customizing output voltage, frequency, and overload settings.

ON;OFF Personalization

Options for start-up behavior, automatic restart, energy saving, and phase inversion.

Battery Personalization

Settings for battery tests, backup time selection, and discharge protection.

4.4 Personalization Using External Software

Guide to using the Personal Solution-Pac software for advanced settings.

5. Maintenance

5.1 Troubleshooting

Table listing indications, diagnostics, and corrections for UPS faults.

Troubleshooting HotSwap MBP Module Issues

Specific troubleshooting steps for UPS units with the HotSwap MBP module.

5.2 Battery Module Replacement

Safety recommendations and procedures for replacing UPS batteries.

Battery Module Removal and Installation

Step-by-step guide to physically remove and install battery modules.

5.3 HotSwap MBP Module Maintenance

Procedures for performing maintenance on UPS with HotSwap MBP.

6. Appendices

6.1 Technical Specifications

Detailed technical data including output power, environment, and electrical specifications.

6.2 Programming the Programmable Outlets

Guide to configuring programmable outlets using the Personal Solution Pac software.

Shutdown Timer Configuration

How to configure shutdown timer for powershare outlets via software.

6.3 Glossary of Terms

Definitions of technical terms used in the manual.