Eaton Power Xpert 9395P - Figure 83. Load off Screen; Figure 84. Typical System Status Screen

142 Eaton Power Xpert 9395 UPS Installation and Operation Manual 164201764—Rev 14
Figure 83. Load Off Screen
HOLD LOAD OFF BUTTON FOR 3 SECONDS
TO TURN OFF LOAD
LOAD OFFCANCEL
77..22..88 SSyysstteemm SSttaattuuss SSccrreeeenn aanndd CCoonnttrroollss
Press the CONTROLS pushbutton on the main menu bar to display the System Status screen. Online
operation, transfer to bypass, charger control, UPM startup and shutdown, and LOAD OFF commands are
controlled through this screen. In addition, the screen displays the current status of the UPS, indicates whether
the UPS is in Maintenance Bypass or Bypass, and displays the state of the UPM and battery charger. Figure 84
shows the System Status screen.
Use the
UPS OPERATING INSTRUCTIONS
EATON 9395 UPS (650–825 kVA) Installation and Operation Manual S 164201725 Rev 4P Draft 31-Jan-2010
7-11
7.2.8 System Status Screen and Controls
Press the CONTROLS pushbutton on the main menu bar to display the System Status
screen. Normal operation, transfer to bypass, charger control, UPM s tartup and
shutdown, and LOAD OFF commands are controlled through this screen. In addition,
the screen displays the current status of the UPS, indicates whether the UPS is in
Maintenance Bypass or Bypass, and displays the state of the UPM and battery
charger. Figure 7-7 shows the Sy stem Status screen.
Use the
or pushbutton on the System Status menu bar to highlight the
command screen desired, then press the
CONTROLS pushbutton to display the
command menu screen.
Table 7-4 lists the typical System Status Screen Messages that are displayed during
UPS operation.
Table 7-5 describes the control functions and provides instructions to access and use
the command menu screens.
For detailed information about us ing the System Controls , see paragraph 7.3.
MAINTENANCE BYPASS
BYP ASS
UPM: OFFLINE
SHUTDOWN:
AVAILABLE:
OFF:
SYSTEM STATUS
CONTROLS ESC
CHARGER OFF:
UPS
Figure 7-7. Typical System Status Screen
Table 7-4. Typical System Status Messages
Function Message
UPS Shutdown; Bypass; Online; Online with ESS; Online +VMMS;
High Alert
Bypass Off; On; Available
Maintenance Bypass Off; On
Charger Charger Off; Charging
UPM (during startup) DC Starting, Charger Off; DC Starting, Close Battery
Breaker; Inverter Starting; Inverter Syncing; Ready; Online
UPM 1
UPM 2
UPM 3
UPM 4 (Plus 1 model only)
Offline; Shutdown, Charger Off; Ready; Ready, Charging;
Online, Charger Off; Online, Charging
or
UPS OPERATING INSTRUCTIONS
EATON 9395 UPS (650–825 kVA) Installation and Operation Manual S 164201725 Rev 4P Draft 31-Jan-2010
7-11
7.2.8 System Status Screen and Controls
Press the CONTROLS pushbutton on the main menu bar to display the System Status
screen. Normal operation, transfer to bypass, charger control, UPM s tartup and
shutdown, and LOAD OFF commands are controlled through this screen. In addition,
the screen displays the current status of the UPS, indicates whether the UPS is in
Maintenance Bypass or Bypass, and displays the state of the UPM and battery
charger. Figure 7-7 shows the Sy stem Status screen.
Use the
or pushbutton on the System Status menu bar to highlight the
command screen desired, then press the
CONTROLS pushbutton to display the
command menu screen.
Table 7-4 lists the typical System Status Screen Messages that are displayed during
UPS operation.
Table 7-5 describes the control functions and provides instructions to access and use
the command menu screens.
For detailed information about us ing the System Controls , see paragraph 7.3.
MAINTENANCE BYPASS
BYP ASS
UPM: OFFLINE
SHUTDOWN:
AVAILABLE:
OFF:
SYSTEM STATUS
CONTROLS ESC
CHARGER OFF:
UPS
Figure 7-7. Typical System Status Screen
Table 7-4. Typical System Status Messages
Function Message
UPS Shutdown; Bypass; Online; Online with ESS; Online +VMMS;
High Alert
Bypass Off; On; Available
Maintenance Bypass Off; On
Charger Charger Off; Charging
UPM (during startup) DC Starting, Charger Off; DC Starting, Close Battery
Breaker; Inverter Starting; Inverter Syncing; Ready; Online
UPM 1
UPM 2
UPM 3
UPM 4 (Plus 1 model only)
Offline; Shutdown, Charger Off; Ready; Ready, Charging;
Online, Charger Off; Online, Charging
pushbutton on the System Status menu bar to highlight the command screen desired, then
press the CONTROLS pushbutton to display the command menu screen.
Table 32 lists the typical System Status Screen Messages that are displayed during UPS operation.
Table 33 describes the control functions and provides instructions to access and use the command menu
screens.
For detailed information about using the System Controls, see paragraph 7.3 Single UPS Operation.
Figure 84. Typical System Status Screen
MAINTENANCE BYPASS
BYPASS
UPM: OFFLINE
SHUTDOWN:
AVAILABLE:
OFF:
SYSTEM STA
TUS
CONTROL
S
ESC
FFOREGRAHC :
UPS
UPS Operating Instructions