Eaton Power Xpert 9395P - Page 19

Eaton Power Xpert 9395 UPS Installation and Operation Manual 164201764—Rev 14 xix
LLiisstt ooff TTaabblleess
Table 1. Storage Area Contaminants 764 ....................................................................................................... 16
Table 2. UPS Cabinet Maximum Weights....................................................................................................... 17
Table 3. UPS Cabinet Clearances ................................................................................................................. 17
Table 4. Air Conditioning or Ventilation Requirements During Full Load Operation................................................... 18
Table 5. Input/Output Ratings and External Wiring Requirements for the Four UPM Power Xpert 9395-1100/1000
and 9395-1100/1100 – Common Battery............................................................................................. 27
Table 6. Input/Output Ratings and External Wiring Requirements for the Four UPM Power Xpert 9395-1100/1000,
and 9395-1100/1100 – Separate Battery ............................................................................................. 29
Table 7. Input/Output Ratings and External Wiring Requirements for the Three UPM Power Xpert 9395-1100/650,
9395-1100/750, and 9395-1100/825 – Common Battery......................................................................... 31
Table 8. Input/Output Ratings and External Wiring Requirements for the Three UPM Power Xpert 9395-1100/650,
9395-1100/750, and 9395-1100/825 – Separate Battery ......................................................................... 33
Table 9. Bonding Requirements for the Four UPM Power Xpert 9395-1100/1000 and 9395-1100/1100 ....................... 34
Table 10. Bonding Requirements for the Three UPM Power Xpert 9395-1100/650, 9395-1100/750, and 9395-1100/
825............................................................................................................................................. 35
Table 11. UPS Intercabinet Power Cable Terminations for the Four UPM Power Xpert 9395-1100/1000 and 9395-
1100/1100, and the Three UPM Power Xpert 9395-1100/650, 9395-1100/750, and 9395-1100/825 ................. 35
Table 12. Supplied Intercabinet Wiring Terminal Hardware Kit .............................................................................. 36
Table 13. UPS External Power Cable Terminations for the Four UPM Power Xpert 9395-1100/1000 and 9395-1100/
1100, and the Three UPM Power Xpert 9395-1100/650, 9395-1100/750, and 9395-1100/825......................... 36
Table 14. Supplied External Wiring Terminal Hardware Kit ................................................................................... 37
Table 15. Recommended Installation Parts and Tools (Not Supplied by Eaton) ......................................................... 37
Table 16. Power Cable Conduit Requirements .................................................................................................. 38
Table 17. Recommended Input Circuit Breaker Ratings ...................................................................................... 39
Table 18. Recommended Bypass, Output, and MOB Circuit Breaker Ratings .......................................................... 39
Table 19. Recommended DC Input Circuit Breaker Ratings – Common Battery........................................................ 40
Table 20. Recommended DC Input Circuit Breaker Ratings – Separate Battery ........................................................ 40
Table 21. TB1, TB2, and TB3 Interface Connections .......................................................................................... 76
Table 22. REPO Wire Terminations ................................................................................................................ 84
Table 23. Powerware Hot Sync CAN Bridge Card Interface Connections ................................................................ 93
Table 24. CAN Bridge Card Wiring Terminations................................................................................................ 96
Table 25. Pull-Chain Wiring Terminations ......................................................................................................... 97
Table 26. Pull-Chain Wiring Terminations with MOBs ........................................................................................ 99
Table 27. RMP II, RIM II, or SCM II Wiring Terminations ................................................................................... 101
Table 28. J1 through J4 Interface Connectors................................................................................................. 102
Table 29. Status Indicators ......................................................................................................................... 135
Table 30. Display Function Menu Map .......................................................................................................... 137
Table 31. Display Menu Operation ............................................................................................................... 138
Table 32. Typical System Status Messages.................................................................................................... 143
Table 33. Command Menu Operation ........................................................................................................... 143
Table 34. Status Indicators ......................................................................................................................... 179