Eaton PowerXL DG1 - Table 82. Required Line and Motor Wire Torque (230 V)

96
Appendix D—Safety instructions for UL and cUL
POWERXL SERIES VFD MN040002EN—February 2018 www.eaton.com
•
For 230 V Drive Series, required line and motor wire
torque, type and size range are listed in Table 80
Table 82. Required line and motor wire torque (230 V)
DG1
catalog number
DH1
catalog number Terminal type
Required
torque (in-lb)
Required
wire range
FR0
DG1-323D7EB-C20C DH1-324D8EB-C20C

L1, L2, L3, DC+, DC-, R+, R-, U, V, W 5.3 14–10 AWG
DG1-324D8EB-C20C DH1-326D6EB-C20C

5.3 14–10 AWG
DG1-326D6EB-C20C DH1-327D8EB-C20C

5.3 14–10 AWG
FR1
DG1-323D7xx-xxxx DH1-324D8XX-XXXX L1, L2, L3, DC+, DC–, R+, R–, U, V, W 5.3 14–10 AWG
DG1-324D8xx-xxxx DH1-326D6XX-XXXX 5.3 14–10 AWG
DG1-326D6xx-xxxx DH1-327D8XX-XXXX 5.3 14–10 AWG
DG1-327D8xx-xxxx DH1-32011XX-XXXX 5.3 14–10 AWG
DG1-32011xx-xxxx DH1-32012XX-XXXX 5.3 12–10 AWG
FR2
DG1-32012xx-xxxx DH1-32017XX-XXXX L1, L2, L3, DC+, DC–, R+, R–, U, V, W 15.6 10–6 AWG
DG1-32017xx-xxxx DH1-32025XX-XXXX 15.6 8–6 AWG
DG1-32025xx-xxxx DH1-32031XX-XXXX 15.6 8–6 AWG
FR3
DG1-32031xx-xxxx DH1-32048XX-XXXX L1, L2, L3, DC+, DC–, R+, R–, U, V, W 40 6–2 AWG
DG1-32048xx-xxxx DH1-32061XX-XXXX 40 4–2 AWG
FR4
DG1-32061xx-xxxx DH1-32075XX-XXXX L1, L2, L3, DC+, DC–, R+, R–, U, V, W 95 3–1/0 AWG
DG1-32075xx-xxxx DH1-32088XX-XXXX 95 2–1/0 AWG
DG1-32088xx-xxxx

DH1-32114XX-XXXX 95 1/0 AWG
1
FR5
DG1-32114xx-xxxx DH1-32143XX-XXXX L1, L2, L3, DC+, DC–, R+, R–, U, V, W 354 3/0 AWG–350 kcmil
DG1-32143xx-xxxx DH1-32170XX-XXXX 354 4/0 AWG–350 kcmil
DG1-32170xx-xxxx DH1-32211XX-XXXX 354 300–350 kcmil
FR6
DG1-32211xx-xxxx DH1-32261XX-XXXX L1, L2, L3, DC+, DC–, R+, R–, U, V, W 480 2*(2/0–300 kcmil)
DG1-32248xx-xxxx DH1-32312XX-XXXX 480 2*(4/0–300 kcmil)
All Frames Sizes (FR0–FR6)
All models Control terminal block 4.5 28~12 (Sol) AWG
30~12 (Str) AWG
otes: N  IP20 FR0 will be available in June 2018.
 The line and motor wire size for DG1-32088xx-xxxx/DH1-320114xx-xxxx can only be 1/0 AWG.