Eaton SVX900 - Input;Output Signal Configuration

MN04003009E
10
December 2003
STEP 4 (Continued)
Input Signals — M1 ➔ G1.2

Parameter value can only be changed when the SVX9000 is stopped.

Rising edge pulse required.
Output Signals — M1 ➔ G1.3
Code Parameter Min. Max. Unit Default Cust ID Note
P1.2.1

Start/Stop logic 0 6 0 300 DIN1 DIN2
0
1
2
3
4
5
6
Start fwd
Start/Stop
Start/Stop
Start pulse
Fwd

Start

/
Stop
Start

/
Stop
Start rev
Rev/Fwd
Run
enable
Stop
pulse
Rev

Rev

/
Fwd
Run
enable

P1.2.2

DIN3 function 0 7 1 301 0 = Not used
1 = Ext. fault, closing
contact
2 = Ext. fault, opening
contact
3 = Run enable
4 = Acc./Dec. time select
5 = Force control pt. to
Local
6 = Force control pt. to
Remote
7 = Rev (if P1.2.1 = 3)
P1.2.3 Current
reference offset
01 1 302 0 = 0 – 20 mA
1 = 4 – 20 mA
P1.2.4 Reference
scaling
minimum value
0.00 P1.2.5 Hz 0.00 303 Selects the frequency that
corresponds to the min.
reference signal
P1.2.5 Reference
scaling
maximum value
0.00 320.00 Hz 0.00 304 Selects the frequency that
corresponds to the max.
reference signal
0.00 = No scaling
P1.2.6 Reference
inversion
01 0 305 0 = Not inverted
1 = Inverted
P1.2.7 Reference filter
time
0.00 10.00 s 0.10 306 0.00 = No filtering
P1.2.8 AI1 signal
selection
AnIN:
0.1
AnIN:
E.10
AnIN:
A.1
377 TTF programming
method used.
P1.2.9 AI2 signal
selection
AnIN:
0.1
AnIN:
E.10
AnIN:
A.2
388 TTF programming
method used.
Code Parameter Min. Max. Unit Default Cust ID Note
P1.3.1 Analog
output 1
signal
selection
AnOUT:
0.1
AnOUT:
E.10
AnOUT:
A.1
464 TTF programming
method used.
P1.3.2 Analog output
function
08 1 307 0 = Not used
1 = Output freq.
(0 – f
Max
)
2 = Freq. reference
(0 – f
Max
)
3 = Motor speed
(0 – Motor nominal
speed)
4 = Motor current
(0 – I
nMotor
)
5 = Motor torque
(0 – T
nMotor
6 = Motor power
(0 – P
nMotor
)
7 = Motor voltage
(0 – V
nMotor
)
8 = DC-Bus volt
(0 – 1000V)
P1.3.3 Analog output
filter time
0.00 10.00 s 1.00 308 0.00 = No filtering
P1.3.4 Analog output
inversion
01 0 309 0 = Not inverted
1 = Inverted
P1.3.5 Analog output
minimum
01 0 310 0 = 0 mA
1 = 4 mA
P1.3.6 Analog output
scale
10 1000 % 100 311 100 = No scaling
MN04003009E.fm Page 10 Thursday, February 17, 2005 11:59 AM