Need help?Do you have a question about the EAW SB Series and is the answer not in the manual?
Guide to designing line array systems using Resolution software.
Details on EAW Resolution 2 software for SPL predictions and rigging calculations.
List of recommended system requirements for Resolution software.
Technical performance data including Max SPL, operating range, and beamwidth.
Transducer and loading details for the KF810P loudspeaker.
Technical performance data for the SB818P|F subwoofer.
Transducer and loading details for the SB818P|F subwoofer.
Technical performance data for the KF210 loudspeaker.
Transducer and loading details for the KF210 loudspeaker.
Technical performance data for the SB818 subwoofer.
Transducer and loading details for the SB818 subwoofer.
Visual examples showing directivity changes with different array lengths.
Recommended amplifier configurations for KF810P using UXA4416.
Recommended amplifier configurations for SB818P|F using UXA4416.
Recommended amplifier configurations for KF210 Bi Amped using UXA4416.
Wiring details for connecting KF810P to UXA4410 amplifier.
Wiring details for connecting KF210 to UXA4410 amplifier in single/bi-amp modes.
Importance of using EAW amplifier with line array products for optimal performance.
Description of the amplifier's front panel buttons, screen, and indicators.
Detailed description of all rear panel connectors and ports.
Pinout and specifications for AES/EBU digital input connectors.
Explanation of Direct Mode and Relay Bypass for signal link management.
Details on connecting and configuring Dante network ports for control and audio.
Guidelines for setting up devices in a daisy chain configuration.
Information on implementing concurrent primary and secondary networks.
Available functions for GPIO input and output contacts on the amplifier.
How the fault contacts warn of general unit faults.
Steps to connect Resolution software to amplifiers on the network.
Methods for assigning an online device to a network processor.
Procedure for adding an offline amplifier to the system.
Process of adding the offline UXA4416 to the model in Resolution.
Dialog for choosing to push or pull settings between online and offline amplifiers.
Troubleshooting steps for assignment issues, including firmware upgrades.
Interface for adjusting PEQ and Shelf filters in the amplifier.
How to choose speaker models and modify settings for amplifier channels.
Adjusting input gain, polarity, and delay for amplifier channels.
Process of selecting and applying speaker models (Greyboxes) to amplifier channels.
How input/output channels behave when a Bi Amp greybox is loaded.
Configuring AES/EBU link outputs and assigning input sources.
How to assign an input source to a corresponding digital output.
Assigning inputs to available Dante channels and renaming inputs.
Selecting main, backup, or auto-selected input sources for DSP.
Visual representation of audio signal flow and meter readings.
Using the Firmware Manager to update device firmware, greyboxes, and Dante firmware.
Important practices to follow before and during firmware upgrades.
Steps to restart the update process if network interruptions occur.
Diagram and description of the UXR amp rack front panel components.
Diagram and description of the UXR amp rack rear panel components.
How to rig UXR amp racks for touring using flybars.
Essential practices for designing safe and effective loudspeaker rigging.
Information on selecting and using third-party rigging hardware.
Steps for attaching the stinger and flybar assembly to the frame.
Procedures for attaching shackles and subsequent array items.
Steps for rigging KF810P arrays when not using an SB818P|F.
Critical safety warnings for ground-stacking arrays.
Step-by-step guide for ground-stacking KF810P on SB818P|F.
Procedures for ground-stacking KF810P without an SB818P|F.
Step-by-step guide for assembling KF210 modules.
Explanation of the rear rigging assembly plate and angle lock mechanism.
Description of KF210 flybar options for installation.
Steps for using the groundstack adapter with KF210 and SB818.
Steps for building arrays using the KF Series transition bar.
How to connect NTX210L to SBX118F using transition bars.
Information on the transport capacity of KF210 and SB818 carts.
Procedure for handling products damaged during shipping.
To Next Page
General
