Bluetooth version
V5.0
Operation distance
10 m
Audio coding format
SBC,AAC,APTX
BT profiles support
HSP, HFP, A2DP, AVRCP
Battery capactity
40mAh for each earbuds
500mAh for charging case
Charging time
Around 2 hours
Playing time
5-6 hours
Talk time
4-5 hours
Standby time Around 70 hours
Frequency range
20-20kHz
Driver unit
6mm
Earbuds weight
5g each
Ear
b
u
d
s
22*40mm
Elecder D18
Wireless Earbuds
Power ON/OFF
Pairing
Stereo Mode:
Mono Mode:
Elecder D18
Multi Functions
Elecder D18
Pause/Play
Single tap L/R
Double tap L
Previous Song
Active Siri/Googel
Assitant
Triple tap L or R
Refuse the call
Answer/End a call
Tap L or R
Long touch L or R
-02-
-01- -03-
-04-
-05-
-06- -07-
-08- -09-
The correct way of wearing
Put earbuds in the ear and gently rotate until 45° above
(as shown below).
Thank you for purchasing your new Elecder D18 true
wireless earbuds.
We recommend that you spend some time reading this
instruction manual in order that you fully understand all
the operational features it offers.
Read all the safety instructions carefully before use and
keep this instruction manual for future reference.
1. Charge the earbuds and the charging case at least once
every 6 months.
2. Do not store the product in extreme temperature
(below 0℃ or above 45℃).
3. Do not use chemicals or detergents to clean the product.
4. Do not drop or knock the product on hard surfaces.
5. Do not scrape the surface of product with sharp objects.
6. Do not try to take the product apart.
Power ON:
When you open the charging case(with battery
power inside), it will be power ON automatically
and blue LED will blink.
When the earbuds L & R is power OFF after taking
out of the charging case, long touch the L & R earbuds
button to turn it on and blue LED will blink.
Power OFF:
When you put the L & R earbuds into the charging
case(with battery power inside), close the charging
case, it will be power OFF automatically.
When the earbuds L & R is power ON after taking out
of the charging case, long touch the L or R earbuds
button to turn it off under BT disconnection status.
Note: Under BT disconnection status more than 5 mins,
the L & R earbuds will be power OFF automatically.
2. Activate Bluetooth on the phone and search for
“Elecder D18” to connect. Blue LED will blink
slowly after connected.
1. Take out both earbuds from the charging case,
the L&R earbuds will be automatically connected.
Blue LED will blink.
1. Take out L or R earbuds from the charging case.
Blue LED will blink.
2. Activate Bluetooth on the phone and search for
“Elecder D18” for L earbuds Or
“Elecder D18 R” for R earbuds.
Blue LED will blink slowly after connected.
Note: In Mono mode, double tap L or R can only
move to next song.
Charging Mode
* Charging: Red LED is on
* Full charged: Blue LED is on & turned off after
about 30s
2. Charging the case by Type-C cable
1. Charging the earbuds
Take earbuds into charge case
* Charging: < 30% battery, Red LED is on
30%-80% battery, Orange LED is on
80%-100% battery, Green LED is on
Safety Rules
-10-
Specifications Product Overview
How to Wear?
Type-C
ENGLISH
ENGLISH ENGLISH ENGLISH
ENGLISH
Multi-Function
Button(MFB)
LED
Indicator
Soft Silicon
Earbud
Charging
Point
Microphone
Charging
Point
Charging
Case LED
Next Song Double tap R
Volume Down
Long touch L for 2s
Volume Up
Long touch R for 2s
In case there is no auto pairing after taking out the
earbuds from the charging case, please follow the
below steps to restore the default setting:
1. Ensure L&R disconnect to any device(trun off
the bluetooth device connected before).
2. Trun off both L&R earpbuds.
3. Long touch MFB button of L&R earbuds around 8s
till both red light flash 3 times. The factory reset is
now finished.
4. The L&R earbuds will be automatically connected
and blue LED will blink. The earbuds is ready to pair
with your device now.
Factory reset
Bluetooth Transmission
Frequency Range:
2402MHz-2480MHz
Max. Transmission
Power (Bluetooth)
8dBm
MADE IN CHINA
3. Charge the case by wireless charger
1. Keep the earbuds away from high temperature
and humidity
2. Do not put the earbuds directly in the sun to burst,
or put it in a high temperature environment, which
will shorten the life of the earbuds (internal department
of electronic components and batteries).
3. Do not try to disassemble the earbuds body.
4. Do not drop the earbuds on a hard surface.
5. Do not use sharp objects to scratch the surface of
the product.
6. Do not use chemicals or detergents to clean the earbuds.
http://www.elecder.net
EARBUDS MANTENANCE:
WARRANTY REGULATIONS:
WARRANTY AND AFTER SALES:
The following conditions are not covered by the warrenty:
1. Because of buying second-hand or used products.
2. Damage caused by irregular operation.
3. Damage caused by natural disasters.
4. Damage caused by chemical substances, open flames,
radioactive substances, toxic substances, liquids.
5. Damage caused by third parties / people / things or others.
If you need after-sales or any help, please contact us
by the email "support@elecder.net", our customer
service will reply you within 24 hours, we will do our
best to solve your problem.
For more information please visit http://www.elecder.net
* Full charged: Green LED is off
Note: 5V/1A or 5V/1.5A is the best choice
for the charger.
To Next Page
Loading...